Effects of Wastewaters From an Abattoir on Surface Water Quality in Akure, Ondo State, Nigeria
- Authors
-
-
O. O. Olubanjo
Department of Agricultural and Environmental Engineering, Federal University of Technology Akure, Ondo State, Nigeria
-
- Keywords:
- Abattoir, Waste water, Parameters, Pollution, water
- Abstract
-
The study examined the effect of Onyearugbulem abattoir wastewaters discharge on surface water quality in Akure. Water samples were taken at three different locations along the receiving water body namely the Upper Course (UC), Middle Course (MC) and the Lower Course (LC). UC samples were collected at the point of entry of the abattoir wastes; MC samples were taken about 50m from the point of entry while LC samples were taken about 100m away from the point of entry of the abattoir waste. The samples were collected, preserved and analyzed in the laboratory using standard methods. The wastewater parameters analyzed were dissolved oxygen (DO), pH, total suspended solid (TSS), total dissolved solid (TDS), biochemical oxygen demand (BOD), chemical oxygen demand (COD), and heavy metals. The mean concentration of 0.24 mg/l for Cr and 0.02 mg/l for Pb exceeded the WHO (1993) and FEPA (1991) standard of 0.1 mg/l Cr and 0.01 mg/l Pb for the discharge of wastewater into river, while the levels of nitrate, TSS and TDS were also higher than the WHO limits for the discharge of wastewater into river. The mean values of 1.9 mg/l, 1626.6 mg/l, 466.67 mg/l and 1666.67 mg/l for DO, COD, TSS and TDS exceeded the WHO permissible limit of ≥5mg/l for DO, N/D for COD, 500 mg/l for TSS and 500 mg/l for TDS for the discharge of wastewater from Onyearugbulem abattoir into the river. Based on the results obtained, the Abattoir Practice Regulatory body should be put in place by the Environmental Protection Agency to regularly regulate and monitor abattoir activities in the study area in order to prevent environmental pollution and health hazards caused by activities of abattoirs.
- References
- Downloads
- Published
- 2019-05-04
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- M. D. IDI, T. A. ALADESANMI, S. LUKMAN, M. A. ASANI, Y. M. USMAN, I. A. OKE, A NUMERICAL FORMULA AND COST BENEFIT OF GROUNDWATER RECHARGE IN MAIDUGURI, NIGERIA , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 2 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- O. O. Olubanjo, A. E. Alade, Development of a Low Cost Greenhouse and Drip Hydroponic Structure for Vegetable Production in South-West Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 1 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- B. Adebayo, Evaluation of the Performance of Atlas Copco SDR4 Rotary Drill In Sagamu Limestone Formation, Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 1 (2019): FUTA Journal of Engineering and Engineering Technology
- J. O. Ojediran, J. T. Fasinmirin, O. P. Owa, Development and Performance Evaluation of an Indigenous Fish Feed Palletizing Machine , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 2 (2017): FUTA Journal of Engineering and Engineering Technology
- O. O. Awopetu, Effect of Rake Face Reinforcement on Cutting Tool Life of Cemented Carbide Tools during Turning of a-Titanium Alloy , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 1 (2017): FUTA Journal of Engineering and Engineering Technology
- J. A. V. Famurewa, C. J. Oladejo, Isotherm Models of Tacca Starch (Tacca Involucrata) at Ambient Temperature Using Some Common Packaging Materials , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 10 No. 2 (2016): FUTA Journal of Engineering and Engineering Technology
- P. M. Enyong, Performance of a Short Transmission Line Module under Various Loads: A Comparative Evaluation , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 2 (2018): FUTA Journal of Engineering and Engineering Technology
- S. S. Yaru, I. K. Adegun, Analyses of Biogas and Digestate from Cattle Dung Anaerobic Digestion , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 2 (2017): FUTA Journal of Engineering and Engineering Technology
- K. F. Akingbade, Development of Chemical Proportion Formulation Model for Quality Control in Flexible Polyurethane Foam Production , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 2 (2017): FUTA Journal of Engineering and Engineering Technology
- Kayode Francis Akingbade, DEVELOPMENT OF CHEMICAL PROPORTION FORMULATION MODEL FOR QUALITY CONTROL IN FLEXIBLE POLYURETHANE FOAM PRODUCTION , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 2 (2018): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.