Conceptual Design of Battery Powered Vehicle for Children Amusement Park Using Nigerian Anthropometric Parameters
- Authors
-
-
S. P. Ayodeji
Department of Industrial and Production Engineering, The Federal University of Technology, Akure, Nigeria
-
M. K. Adeyeri
Department of Industrial and Production Engineering, The Federal University of Technology, Akure, Nigeria
-
O. O. Oni
Department of Industrial and Production Engineering, The Federal University of Technology, Akure, Nigeria
-
- Keywords:
- Conceptual Design, Battery Powered Vehicle, Children, Amusement Park, Anthropometric Parameters
- Abstract
-
Exercise helps children to be active and lack of it can lead to boredom. The problem of unavailability of facilities designed for children amusement park using the right anthropometric parameters and the procurement cost due to importation duties have been a big challenge. Provision of children vehicle for amusement park using anthropometric parameters will go a long way to solve the problems associated with boredom. Anthropometric parameters from 2 5 0 (150 male and I 00 female) children between ages 3 to I 2 were collected and analysed. The 5th, 25th, 50th, 75th and 95th percentiles for female and male respectively were used in the design of the children vehicle. Detailed drawings and simulation of the design concept were produced on Autodesk Inventor CAD software. Three deep cycle battery of 200Ah x 12V each was proposed as the energy driver that will drive the vehicle for 1 hr at a carrying load capacity of 2280N. The simulation result ensure the stability of the vehicle.
- References
- Downloads
- Published
- 2019-05-05
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- T E Abioye, DEVELOPMENT OF A POULTRY DE-FEATHERING MACHINE WITH AN ADJUSTABLE BASIN , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 1 (2018): FUTA Journal of Engineering and Engineering Technology
- J T Fasinmirin, D O Rapheal, J Lazarus, SOIL CHARCTERIZATION AND MAIZE (Zea mays L.) EVAPOTRANSPIRATION (ETc) IN OMU-ARAN HUMID GEOLOGICAL ZONE OF NIGERIA , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 1 (2018): FUTA Journal of Engineering and Engineering Technology
- Robert Oluwayimika Abolade, Oluwaseun Olayinka Tooki, David Oluwagbemiga Aborisade, REVIEW ARTICLE ON THE MITIGATION OF FOUR WAVE MIXING IN OPTICAL COMMUNICATION SYSTEM , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 1 (2021): FUTA Journal of Engineering and Engineering Technology
- Olufemi Adeyemi Adetola, M. J. Odu, THE DEVELOPMENT OF A HAND-PUSH WEEDER FOR CUTTING WEEDS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 2 (2021): FUTA Journal of Engineering and Engineering Technology
- J. T. Fasinmirin, A. J. Adesigbin, Tillage Effects on Some Soil Physical Properties and Yield of Cowpea (Vigna unguiculata) in the Humid Rain Forest of Akure, Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 9 No. 2 (2015): FUTA Journal of Engineering and Engineering Technology
- A. M. Akintade, O. J. Olukunle, J. Isa, Performance Evaluation of an Electromechanical Groundnut Roasting Machine Akintade A.M, Olukunle O. J. and Isa J. , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 8 No. 2 (2014): FUTA Journal of Engineering and Engineering Technology
- C. O. Ijagbemi, Design and Optimization of A Gas Turbine Waste Heat Recovery System , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 2 (2019): FUTA Journal of Engineering and Engineering Technology
- T. I. Mohammed, ACHIEVING THE SELECTION OF OPTIMAL PRESS BRAKE DESIGN VIA A FUZZY TOPSIS APPROACH , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 2 (2021): FUTA Journal of Engineering and Engineering Technology
- E. O. Ajaka, O. C. Chukwuma, Promax2100: A Computer Programme for Design and Optimization of Mineral Processing Plant , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 8 No. 1 (2014): FUTA Journal of Engineering and Engineering Technology
- F. O. Ajibade, J. R. Adewumi, Performance Evaluation of Aquatic Macrophytes in a Constructed Wetland for Municipal Wastewater Treatment , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 1 (2017): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.