Mechanical Wear Resistance and Water Absorption Properties of Particulate Palm Kernel Shell Reinforced Epoxy Composites for Automobile Application
- Authors
-
-
A. S. Taiwo
Department of Metallurgical and Materials Engineering, The Federal University of Technology, Akure, Ondo State, Nigeria
-
I. O. Oladele
Department of Metallurgical and Materials Engineering, The Federal University of Technology, Akure, Ondo State, Nigeria
-
O. O. Daramola
Department of Metallurgical and Materials Engineering, The Federal University of Technology, Akure, Ondo State, Nigeria
-
A. D. Akinwekomi
Department of Metallurgical and Materials Engineering, The Federal University of Technology, Akure, Ondo State, Nigeria
-
O. G. Agbabiaka
Department of Metallurgical and Materials Engineering, The Federal University of Technology, Akure, Ondo State, Nigeria
-
- Keywords:
- Mechanical properties, wear resistance, water absorption, palm kernel shell, epoxy, automobile, composites
- Abstract
-
This work investigates the effects of particulate palm kernel shell (PKS) on epoxy matrix for the development of composites that can be used as substitute to the conventional metallic bumpers in automobiles. The PKS was sourced from an oil plantation and washed thoroughly with water before sun dried. The dried PKS was pulverized using a laboratory ball mill and sieved into 45 µm particle sizes. Elemental composition of the PKS was determined using XRF. The PKS particulate was randomly dispersed in the epoxy resin to develop composite samples of varied weight contents. The developed samples were tested to determine their impact toughness, wear resistance, flexural, tensile and water absorption properties. The results showed that higher weight contents within 10 - 20 wt.% PKS reinforcement gave the best performance in most of the mechanical properties examined with the exception of tensile and flexural properties which were enhanced at 8 wt.%. Water absorption was noticed to increase as the PKS content increases from 2 - 20 wt.%.
- References
- Downloads
- Published
- 2019-05-14
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- I. O. Oladele, O. G. Agbabiaka, O. S. Akinola, H. K. Talabi, Development of Sponge Fiber and Particulate Palm Kernel Shell Ash Reinforced Polypropylene Hybrid Composites , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 10 No. 2 (2016): FUTA Journal of Engineering and Engineering Technology
- Aderinola, O.S, Ata, G.O, ENHANCING ASPHALT PAVEMENT PERFORMANCE THROUGH PALM KERNEL SHELLS (PKS) INTEGRATION , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 1 (2025): FUTA Journal of Engineering and Engineering Technology
- O O. Daramola, MECHANICAL PROPERTIES AND WEAR BEHAVIOUR OF KAOLINITE CLAY PARTICLES REINFORCED EPOXY MATRIX COMPOSITES , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 2 (2021): FUTA Journal of Engineering and Engineering Technology
- Dafiewhare, O, Ijagbemi, C. O, Ologunwa, T. P, Alabi, O. T, Ijagbemi, A. O, PRODUCTION AND EVALUATION OF BIOMASS BRIQUETTES FROM PALM KERNEL SHELL AND COCONUT HUSK , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 2 (2025): FUTA Journal of Engineering and Engineering Technology
- O. O. Daramola, I. O. Oladele, O. S. AKINTAYO, MECHANICAL PROPERTIES OF EPOXY MATRIX COMPOSITES REINFORCED WITH GARLIC PARTICLES , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 2 (2021): FUTA Journal of Engineering and Engineering Technology
- I O OLADELE, O O DARAMOLA, A M OKORO, J A OMOTOYINBO, EVALUATION OF THE EFFECT OF MERCERIZED WHITE CHICKEN FEATHER FIBRES ON THE MECHANICAL , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 1 (2018): FUTA Journal of Engineering and Engineering Technology
- P. B. Mogaji, T. E. Abioye, N. O. Ohuruogu, Development of Epoxy Resin Composite Reinforced With Cow Horn and Cassava Particles for Car Dashboard , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 1 (2017): FUTA Journal of Engineering and Engineering Technology
- Oluseyi Orisadare, Ayodeji S. Olawore, Michael O. Ibiwoye, Eyitayo A. Ponle, Omolola T. Odeyemi, Opeyemi S. Kegbeyale, MECHANICAL AND MICROSTRUCTURAL PROPERTIES OF BRASS REINFORCED WITH COCONUT SHELL ASH POWDER , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 2 (2021): FUTA Journal of Engineering and Engineering Technology
- IDOWU Abimbola Samson , ADEWUYI B.O, FOLORUNSO D.O, AKINWEKOMI A. D., OPTIMUM INFLUENCE OF CHROMIUM AND COMBINE AUSTEMPERING-CRYOGENIC TREATMENTS ON PERFORMANCE OF DUCTILE IRON , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 1 (2025): FUTA Journal of Engineering and Engineering Technology
- E. O. Olutomilola, T. I. Ogedengbe, Evaluation of the Effect of Constituents on Insulation Quality of Selected Biomass Composites , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 1 (2017): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.