A NUMERICAL FORMULA AND COST BENEFIT OF GROUNDWATER RECHARGE IN MAIDUGURI, NIGERIA
- Authors
-
-
M. D. IDI
Land, Air and Water Consulting, F6 Ibrahim Taiwo Estate, Baga Road, Maiduguri, Borno State, Nigeria
-
T. A. ALADESANMI
Information Technology and Communications Unit, Obafemi Awolowo University, Ile- Ife, Nigeria
-
S. LUKMAN
Civil Engineering Department, University of Hafr Al-Batin, Hafr Al-Batin, Saudi Arabia
-
M. A. ASANI
4 Department of Urban and Regional Planning, Ladoke Akintola University Technology, Ogbomoso, Nigeria
-
Y. M. USMAN
Department of Agricultural Engineering, Ramat Polyechnic Maiduguri
-
I. A. OKE
Department of Civil and Environmental Engineering, Elizade University, Ilara- Mokin, Nigeria
-
- Keywords:
- Groundwater recharge, soil –moisture, , numerical solution, Microsoft Excel Solver, Maiduguri
- Abstract
-
In this paper, relationship between rainfall and groundwater recharge (GR) was established and evaluated with cost benefit. Rainfall measured in Maiduguri, Nigeria was used to fix the unknown constants of the numerical formula (NF) using Microsoft Excel Solver. The constants were used to establish NF. The NF was used to estimate GR from the rainfall. Accuracy of the NF was evaluated statistically (relative error; the degree of accuracy, numerical reliability, Model of Selection Criterion (MSC) and Akaike Information Criterion (AIC)) and compared with the formulae in use using field GR Uttar Pradesh (UP) method as the reference GR. A basic cost benefit of GR was conducted.
The study revealed that GR using the current models were similar to GR using UP, Chaturvedi, Kumar and Seethapathi and Rao, but different in magnitude of GR. NF provided the lowest relative error of 0.146 %, the highest MSC of 13.436; the degree of accuracy of 99. 854 % and the lowest AIC of 43.348 with Rao formula having highest relative error of 56.56 %, the lowest MSC of 0.96; the degree of accuracy of 43.44 % and the lowest AIC of 1403.43. The present average cost benefit of groundwater recharge in Maiduguri was found to be 619.60US $ m-2Yr-1. It was concluded that GR using the numerical formula is a promising tool for GR with minimum error in water resources management.
- References
- Downloads
- Published
- 2020-11-18
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- M. K. Adeyeri, Proposition of Agent-based Preventive Maintenance Algorithm for Hammer Mill Machine Upkeep , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 10 No. 1 (2016): FUTA Journal of Engineering and Engineering Technology
- O. O. Awopetu, P. K. Farayibi, K. A. Ismail, Optimization of Major Process Parameters for Surface Roughness of ASTM 25 Grey Cast Iron using Taguchi method , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 2 (2017): FUTA Journal of Engineering and Engineering Technology
- A. S. Abubakar, Y. A. Sha'aban, Multiple Model Predictive Control for DFIG Based Wind Energy Conversion System , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 1 (2019): FUTA Journal of Engineering and Engineering Technology
- C. M. Ikumapayi, C. Arum, Pozzolanic Influence of Bagasse Ash on the Compressive Strength and Dry Shrinkage of Concrete , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 2 (2019): FUTA Journal of Engineering and Engineering Technology
- Abayomi Olayiwola Eruola, Akeem Makinde, Gbenga Adegboyega Eruola, Kolawole Ayoola, Lugard Nwamini, EFFECT OF FLOAT-WEIGHTS ON DISCHARGE MEASUREMENT , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 1 (2021): FUTA Journal of Engineering and Engineering Technology
- D.O. Folorunso, A. A. Akinwande, INFLUENCE OF WOOD SAW DUST AND WASTE GLASS ADMIXTURE ON SELECTED PROPERTIES OF FIRED CLAY BRICKS FOR MASONRY , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 1 (2021): FUTA Journal of Engineering and Engineering Technology
- Oluwatoyin Olaseinde, O. Ajanaku, O. M. Ojo, S. O. Seidu, COMPARATIVE STUDY OF THE REINFORCED STEEL BARS OBTAINED FROM A FAILED RESIDENTIAL BUILDING AND THE SHELVES , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 2 (2021): FUTA Journal of Engineering and Engineering Technology
- A. P. Olalusi, M. S. Obot, A. S. Ogunlowo, Modelling the Dehydration Characteristics of Taro (Colocasia Esculenta) Slices in a Convective Cabinet Dryer , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 8 No. 1 (2014): FUTA Journal of Engineering and Engineering Technology
- S. S. Yaru, I. K. Adegun, M. A. Akintunde, Comparative Study on Ignition Time of Biogas from Cattle Dung and Mixtures of Cattle Dung with Cassava Peels , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 9 No. 1 (2015): FUTA Journal of Engineering and Engineering Technology
- E O Olutomilola, A Omoaka, THEORETICAL DESIGN OF A PLANTAIN PEELING MACHINE , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 2 (2018): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.