EXPERIMENTAL STUDY ON BED-TO-TUBE HEAT TRANSFER COEFFICIENTS IN BUBBLING FLUIDIZED BED
- Authors
-
-
Bamiji Zacheous Adewole
Obafemi Awolowo University, Ile-Ife, Osun State
-
- Keywords:
- Fluidized bed, Co-firing, Coal, Coconut shell, Bed-to-tube, Heat transfer
- Abstract
-
The overall bed-to-tube heat transfer coefficients of the blends of Lafia-obi coal and coconut shells have been investigated in a bubbling fluidized bed combustor. Experiments were performed at five different particle sizes of coal (5, 10, 15, 20 and 25 mm) and five different particle sizes of coconut shells (2, 6, 10,14 and 18 mm) for different blend proportions of 10%, 20%, 30%, 40% and 50%. Results obtained showed that the overall bed-to-tube heat transfer coefficient decreased with increasing coconut shell particle size in the blends. Combined effects of high radiation from large particle size of coal (25 mm) and high convection heat from small particle size of coconut shell (2 mm) at blend proportion of 10 and 50% produced the maximum bed-to-tube heat transfer coefficient. Due to the importance of heat exchange in the fluidized bed, it is observed that the contribution of biomass co-firing with coal is significant, hence, co-firing at optimal particle size and biomass blend ratio is imperative for achieving higher bed-to-tube heat transfer in the fluidized bed boiler.
- References
- Downloads
- Published
- 2021-11-29
- Section
- Articles
- License
-
Copyright (c) 2021 FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY

This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- T. S. Mogaji, A. Akinsade, M. A. Akintunde, Pyrolysis of Sugarcane Bagasse for Bio-Oil Production , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 2 (2019): FUTA Journal of Engineering and Engineering Technology
- E. O. Olutomilola, T. I. Ogedengbe, Evaluation of the Effect of Constituents on Insulation Quality of Selected Biomass Composites , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 1 (2017): FUTA Journal of Engineering and Engineering Technology
- Babatunde Oluwamayokun Soyoye, Tehinse, T. O., Design and Fabrication of a Maize Shelling Machine , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 2 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- I. A. Oke, A. O. Obijole, E. A. Adekunbi, J. O. Babajide, M. D. Idi, T. A. Aladesanmi, THERMAL PROPERTY OF CARBON RESIN ELECTRODES DEVELOPED FOR ELECTROCHEMICAL TREATMENT OF WATER AND WASTEWATERS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 1 (2021): FUTA Journal of Engineering and Engineering Technology
- M. A. Akintunde, K A ADETORO, T. J. Abioye, Development of Refrigeration System for Storage and Preservation of Yam Tubers , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 2 (2019): FUTA Journal of Engineering and Engineering Technology
- O. Z. Ayodeji, A. A. Adegun, S. A. Anjorin, DEVELOPMENT AND PERFORMANCE EVALUATION OF A SMALL-SCALE GROUNDNUT SHELLING MACHINE , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 2 (2021): FUTA Journal of Engineering and Engineering Technology
- T. S. Mogaji, Development of an Improved Vapour Compression Refrigeration System for Preservation of fresh Vegetables , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 1 (2019): FUTA Journal of Engineering and Engineering Technology
- M. A. Tijani, W. O. Ajagbe, O. A. Agbede, Modelling the Effect of Burning Temperature and Time on Chemical Composition of Sorghum Husk Ash for Optimum Pozzolanic Activity , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 2 (2018): FUTA Journal of Engineering and Engineering Technology
- K.O. OLADOSU, E.O. OLAFIMIHAN, O.R. OYETUNJI, M.O. ADEOTI, A.A. ADEJARE, Influence of Kaolin Additive on Ash Yield of Palm Kernel-Cashew Shell Combustion: Effect of Kaolin Additive on Ash Yield of Palm Kernel- Cashew Shell Combustion , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 2 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- O.O. Ojo,, B.V. Eyiowuawi,, J.F. Akinfolarin,, MECHANICAL AND MORPHOLOGICAL FEATURES OF MICROWAVE HYBRID HEATING-INDUCED WELDING OF SS304 STAINLESS STEEL WITH COKE AS A SUBSECTOR , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 9 No. 2 (2015): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.
