Pozzolanic Influence of Bagasse Ash on the Compressive Strength and Dry Shrinkage of Concrete
- Authors
-
-
C. M. Ikumapayi
Department of Civil and Environmental Engineering, Federal University of Technology, P.M.B 704, Akure
-
C. Arum
Department of Civil and Environmental Engineering, Federal University of Technology, P.M.B 704, Akure,
-
- Keywords:
- Bagasse ash, Concrete, Compressive strength, Drying shrinkage, Pozzolan
- Abstract
-
Partial replacement of cement by pozzolans has been reported to be beneficial to the construction industries. Some of the benefits include higher compressive strength, better resistance to aggressive compound or ions such as chloride ion, sulphate and mild acid. There is the need to analyse some emerging agro-based potential supplementary cementitious materials for their suitability as pozzolans and establish their required optimum dosages for maximum benefits before they can be confidently accepted as pozzolans. Therefore, this research work aims at investigating the suitability of sugarcane bagasse ash as pozzolans; through the determination of its chemical composition, compressive strength and drying shrinkage of the concrete produced from it. Concrete cubes of size 150 mm x 150 mm x 150 mm were produced and crushed at various mass percentage replacement of ordinary Portland cement with bagasse ash at 2% interval from 0% to 18% in order to determine their compressive strength. The drying shrinkage was also determined by using concrete specimens of 75 mm × 75 mm × 250mm dimension at various pozzolanic percentage replacements. The result shows that partial replacement of bagasse ash with ordinary Portland cement will give an improved concrete in terms of compressive strength and with no significant alteration to the drying shrinkage. The optimum mix percentage replacement of ordinary Portland cement with sugarcane bagasse ash was obtained at 12%.
- References
- Downloads
- Published
- 2019-11-17
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- E. O. Aiyewalehinmi, O. S. Aderinola, Strength Properties of Commercially Produced Sandcrete block in Ikeja: Lagos State , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 9 No. 1 (2015): FUTA Journal of Engineering and Engineering Technology
- D.O. Folorunso, A. A. Akinwande, INFLUENCE OF WOOD SAW DUST AND WASTE GLASS ADMIXTURE ON SELECTED PROPERTIES OF FIRED CLAY BRICKS FOR MASONRY , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 1 (2021): FUTA Journal of Engineering and Engineering Technology
- Samuel L Akingbonmire, L Samuel, O Oluwafemi Omotayo, J O Afolayan, A Banjo Olorunshola, THE PHYSICO-CHEMICAL PROPERTIES OF SOME FINE AGGREGATES IN LOKOJA, NIGERIA , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 2 (2018): FUTA Journal of Engineering and Engineering Technology
- O.A. ADEMESO, B.I. ADEYEMO, Physical and Mechanical Characteristics of the Conglomeratic Layer in Akure, Southwestern Nigeria. , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 2 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- Oluwatoyin Olaseinde, O. Ajanaku, O. M. Ojo, S. O. Seidu, COMPARATIVE STUDY OF THE REINFORCED STEEL BARS OBTAINED FROM A FAILED RESIDENTIAL BUILDING AND THE SHELVES , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 2 (2021): FUTA Journal of Engineering and Engineering Technology
- A. J. Abegunde, B. V. Omidiji, P. O. Ajewole, Characterization of Ado-Ekiti River Sand for foundry applications , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 2 (2017): FUTA Journal of Engineering and Engineering Technology
- Samuel Olugbenga Oladele, MODELLING OF THIN-LAYER MICROWAVE DRYING OF BITTER LEAF SAMPLES (Vernonia Amygdalina) FOR PRESERVATION , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 1 (2018): FUTA Journal of Engineering and Engineering Technology
- O. O. Daramola, I. O. Oladele, O. S. AKINTAYO, MECHANICAL PROPERTIES OF EPOXY MATRIX COMPOSITES REINFORCED WITH GARLIC PARTICLES , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 2 (2021): FUTA Journal of Engineering and Engineering Technology
- C. O. Ijagbemi, D. T. Oloruntoba, A. O. Adeoye, Development of a Bioplastic Film for Food Packaging , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 8 No. 1 (2014): FUTA Journal of Engineering and Engineering Technology
- A. S. Oyerinde, EFFECT OF DRYING RATE AND MOISTURE REMOVAL ON THE DRYING PROPERTIES OF GROUND AND FERMENTED CASSAVA MASH ("GARI") , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 1 (2021): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.