MECHANICAL PROPERTIES OF EPOXY MATRIX COMPOSITES REINFORCED WITH GARLIC PARTICLES
- Authors
-
-
O. O. Daramola
3Department of Metallurgical and Materials Engineering, Federal University of Technology, Akure, PMB 704, Nigeria
-
I. O. Oladele
Department of Metallurgical and Materials Engineering, Federal University of Technology, Akure, PMB 704, Nigeria
-
O. S. AKINTAYO
Department of Metallurgical and Materials Engineering, Federal University of Technology, Akure, PMB 704, Nigeria
-
- Keywords:
- Epoxy resin, Garlic, Submicron particles, Mechanical properties, Composite
- Abstract
-
Epoxy resin with different weight fractions of submicron garlic particles were used to develop epoxy composites. Mechanical properties (tensile, flexural and impact) of the developed composites were characterized. The microstructure of tensile fractured surfaces was examined by Scanning Electron Microscope (SEM) in order to identify the relevant fracture modes involved. Results showed that the tensile strength, tensile modulus, flexural strength, flexural stiffness and impact strength was enhanced in the composites with the tensile strength, tensile modulus and impact strength experiencing peak values at 8 wt.% garlic loading before decreasing. Flexural strength and stiffness increased in a linear mode while elongation at break was found to reduce slightly in the composites when compared to the neat epoxy resin. Microstructure revealed the brittle nature of the neat epoxy. Individual particles with low degree of aggregation were observed in the composites with lower loading. However, particles agglomeration was observed in the highly filled composite (10 wt% garlic) resulting in the termination of the linear increase experienced in the tensile strength, tensile modulus and impact strength results. Overall, the test results demonstrate the competency of garlic particles to serve as a reliable, cost effective and efficient reinforcement material for the development of epoxy reinforced composites.
- References
- Downloads
- Published
- 2025-12-08
- Section
- Articles
- License
-
Copyright (c) 2021 FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY

This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- A. P. Olalusi, Comparison of Selected Engineering Properties of Two Species of Cocoyam Essential for Handling of the Tubers , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 8 No. 2 (2014): FUTA Journal of Engineering and Engineering Technology
- E. I. Bello, I. A. Daniyan, T. I Ogedengbe, L. Lajide, P. B. Mogaji, Development of a Model for Predicting the Yield of Biodiesel During Biodiesel Production , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 1 (2017): FUTA Journal of Engineering and Engineering Technology
- S. O. Obayopo, F. J. Banjoko, S. A. Balogun, H. B. Adedayo, Investigation into the Use of Blended Sunflower Oil and Superolein in Hydraulic Systems , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 1 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- Oluwatoyin Olaseinde, O. Ajanaku, O. M. Ojo, S. O. Seidu, COMPARATIVE STUDY OF THE REINFORCED STEEL BARS OBTAINED FROM A FAILED RESIDENTIAL BUILDING AND THE SHELVES , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 2 (2021): FUTA Journal of Engineering and Engineering Technology
- Ashiru Mohammed, Ibrahim Aliyu, Hussaini Abdullahi Umar, Aliyu Umar Mani, PERFORMANCE EVALUATION OF RAILWAY BALLAST DEGRADATION USING THE MORPHOLOGICAL PROPERTIES , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 2 (2021): FUTA Journal of Engineering and Engineering Technology
- I. A. Daniyan, E. I. Bello, T. I. Ogedengbe, L. Lajide, P. B. Mogaji, Development of a Model For Predicting the Yield of Biodiesel During Biodiesel Production , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 10 No. 1 (2016): FUTA Journal of Engineering and Engineering Technology
- O.O. Ojo,, B.V. Eyiowuawi,, J.F. Akinfolarin,, MECHANICAL AND MORPHOLOGICAL FEATURES OF MICROWAVE HYBRID HEATING-INDUCED WELDING OF SS304 STAINLESS STEEL WITH COKE AS A SUBSECTOR , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 9 No. 2 (2015): FUTA Journal of Engineering and Engineering Technology
- T. S. Mogaji, A. Akinsade, M. A. Akintunde, Pyrolysis of Sugarcane Bagasse for Bio-Oil Production , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 2 (2019): FUTA Journal of Engineering and Engineering Technology
- J S. Ajiboye, B. A. Okey-Amechi, Influence of Accumulative back Extrusion and Lubricants on the Hardness of Al 6063 Alloy , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 9 No. 2 (2015): FUTA Journal of Engineering and Engineering Technology
- A. Fadeyibi, Z. D. Osunde, M. G. Visa, A. A. Okunola, Investigation into properties of starch-based nanocomposite materials for fruits and vegetables packaging - A review , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 1 (2017): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.
