ASSESSMENT OF GROUNDNUT SHELL ASH AND SAWDUST ASH AS PARTIAL REPLACEMENT OF CEMENT IN CONCRETE
- Authors
-
-
Tasiu Ashiru Sulaiman
Ahmadu Bello University, Zaria
-
Ibrahim Aliyu
-
Yusuf Yau
-
Ibrahim Bello
-
- Keywords:
- Groundnut Shell Ash (GSA), Sawdust Ash (SDA), workability, compressive strength, and pozzolana
- Abstract
-
This study is aimed at evaluating the combined effect of groundnut shell ash and sawdust ash (GSA/SDA) as partial replacement of ordinary Portland cement in concrete using 1:2:4 mix ratio. The ashes were obtained by the uncontrolled burning process and ground after cooling, the burnt ash was passed through a 75 microns BS sieve. Cement was replaced with 0%, 5%, 10%, 15%, and 20% of GSA/SDA and a water-cement ratio of 0.6 was used. Concrete cubes of 100mm x 100mm x 100mm were cast and cured in water for 3, 14, 21 and 28 days respectively. The result of workability shows that as the GSA/SDA content increased the workability (slump) decreased, but setting times and soundness of GSA/SDA-cement paste increases as the GSA/SDA content increases. However, the compressive strength of GSD/SDA-concrete increases as the curing age increases, and it also increases as the GSD/SDA content increases up to 10% at 28 days then decreases. Finally, it can be concluded that SDA is suitable material for use as a pozzolan since it satisfied the requirement for such a material by having a combined (SiO2+ Al2O3 + Fe2O3) of more than 70%, which was classified as a class C pozzolana, while GSA is a low reactive pozzolan and the optimum percentage of the GSA/SDA to be used should not be more than 10% replacement.
- References
- Downloads
- Published
- 2020-11-18
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- A. A. Ponnle, S. K. Ani, Assessment of Exposure to Indoor Power Frequency Magnetic Fields: SEET Building and Engineering Laboratories, FUTA , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 1 (2019): FUTA Journal of Engineering and Engineering Technology
- A. P. Olalusi, Comparison of Selected Engineering Properties of Two Species of Cocoyam Essential for Handling of the Tubers , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 8 No. 2 (2014): FUTA Journal of Engineering and Engineering Technology
- J. M. Jabar, L. Lajide, A. O. Adetuyi, B. J. Owolabi, G. W. Ayoade, Chemical Modification of Coir, Empty Fruit Bunch and Palm Kernel Fibres for Polymer Reinforcement , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 1 (2017): FUTA Journal of Engineering and Engineering Technology
- Ijagbemi, C.O. , Olabanji, O. M, Abdulmumuni, B, Ashiru, A.R, IJagbemi F.M, PRODUCTION OF ETHANOL GEL FROM CASSAVA AND BANANA PEELS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 1 (2025): FUTA Journal of Engineering and Engineering Technology
- D. T. Oloruntoba, S. O. Seidu, Effect of Mill Scale Particulate in Sand Mould on the Microstructure and Mechanical Properties of Cast 6063 Aluminium Alloys , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 8 No. 2 (2014): FUTA Journal of Engineering and Engineering Technology
- Babatunde Oluwamayokun Soyoye, Tehinse, T. O., Design and Fabrication of a Maize Shelling Machine , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 2 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- Oladele, Samouel O., COMPARATIVE PROXIMATE COMPOSITION AND TOTAL PHENOLIC CONTENTS OF FOUR Musa CULTIVARS AT UNRIPE AND RIPE STAGES , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 1 (2025): FUTA Journal of Engineering and Engineering Technology
- Ijagbemi, C.O, Olabanji, O. M, Ashiru, A.R, Abdulmumuni, B, IJagbemi F.M, DEVELOPMENT OF ETHANOL GEL COOK STOVE , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 1 (2025): FUTA Journal of Engineering and Engineering Technology
- I O OLADELE, O O DARAMOLA, A M OKORO, J A OMOTOYINBO, EVALUATION OF THE EFFECT OF MERCERIZED WHITE CHICKEN FEATHER FIBRES ON THE MECHANICAL , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 1 (2018): FUTA Journal of Engineering and Engineering Technology
- K. O. Oladosu, E. O. Olafimihan, K. A. Babatunde, B. Kareem, A. A. Mustapha, Investigation of Staged Air supply on Grate Combustion of Palm Kernel Shell Mixed with Selected additives (Al2O3 and CaO) , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 1 (2019): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.