PROGRESSIVE FAILURE ANALYSIS OF MULTI-STOREY REINFORCED CONCRETE BUILDINGS UNDER DIFFERENTIAL SETTLEMENT
- Authors
-
-
S. A. Alabi
Department of Civil Engineering, the Federal University of Technology, Akure, Nigeria
-
I. A. Arighaye
Ondo State Ministry of Works, Department of Planning, Design, Research and Statistics, Akure, Nigeria
-
J. O. Afolayan
Department of Civil Engineering, the Federal University of Technology, Akure, Nigeria
-
- Keywords:
- Progressive failure, demand-capacity ratio, differential settlement, multiÂ-storey building, alternative load path method
- Abstract
-
Multi-Storey buildings are buildings with many floors above the ground floor, which serve as shelters for man, his properties and activities. Most building/ails because they were only designed for normal loads whereas abnormal loads were not considered. Therefore, this paper investigates the potential for progressive failure of multi-storey reiriforced concrete (RC) buildings under chosen varying degrees of settlement ranging between 2 5 mm and 15 0 mm. The computer-based modelling procedure following Alternative Load Path Method is adopted for progressive failure analysis. A 5-typical frame models based on the beams' cross-sectional dimensions were analyzed. Each of the frames is analyzed under the normal loads, combining with the assumed differential settlement. From the results obtained, it is discovered that the potential for progressive failure of a multi-storey RC building increases with the increase in the degree of differential settlement. At 25 mm to 75 mm settlement, vulnerability to progressive failure is very low as the Demand-Capacity-Ratio (DCR) values of the component members are very small, but from I 00 mm settlement and above the structure exhibits high potential for progressive failure. It is also noted that the potential for progressive failure of the structure decreases upwards the building storeys. The potential for progressive failure is higher in the lower floors than in the upper floors. Also, the rigidity of the structure helps in combating progressive failure under differential settlement.
- References
- Downloads
- Published
- 2020-04-09
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- A. R. Iyanda, O. A. Odejobi, Computational Modelling Technique for Short-Term Electric Load Forecasting , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 9 No. 2 (2015): FUTA Journal of Engineering and Engineering Technology
- O. A. Awodele, Appraisal of Risk Identification and Response Techniques adopted on Building Projects in Rivers State, Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 10 No. 1 (2016): FUTA Journal of Engineering and Engineering Technology
- S. O. Olatunji, Drivers of Timely Payment in Public Building Projects in Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 2 (2019): FUTA Journal of Engineering and Engineering Technology
- Samuel Olusola Olatunji, An Assessment of the Barriers of Timely Payment in Public Building Projects in Ekiti State, Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 1 (2019): FUTA Journal of Engineering and Engineering Technology
- I. O. Oladele, O. O. Daramola, A. Oyetunji, Appropriate Technological Procedures for Fusion Welding of Low Alloy Carbon Steel , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 8 No. 1 (2014): FUTA Journal of Engineering and Engineering Technology
- A. S. Abubakar, Y. A. Sha'aban, Multiple Model Predictive Control for DFIG Based Wind Energy Conversion System , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 1 (2019): FUTA Journal of Engineering and Engineering Technology
- O. A. Adetola, O. J. Olukunle, T. L. Aremu, Investigation of The Effects of Yield On Selected Physical Properties of Cassava Tubers , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 10 No. 2 (2016): FUTA Journal of Engineering and Engineering Technology
- F. O. Ajibade, J. R. Adewumi, Performance Evaluation of Aquatic Macrophytes in a Constructed Wetland for Municipal Wastewater Treatment , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 1 (2017): FUTA Journal of Engineering and Engineering Technology
- E. I. Bello, I. A. Daniyan, T. I Ogedengbe, L. Lajide, P. B. Mogaji, Development of a Model for Predicting the Yield of Biodiesel During Biodiesel Production , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 1 (2017): FUTA Journal of Engineering and Engineering Technology
- Olatunji Oladimeji Ojo, Taban Emel, ASSESSMENT OF EFFECTIVE NUGGET SIZE, NUGGET ROTATION AND FAILURE MODE OF FRICTION STIR SPOT WELDS OF AA2219-O ALLOY , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 1 (2018): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.