SYNERGISTIC EFFECT OF CO-DIGESTING DIFFERENT MIX RATIOS OF WATER HYACINTH AND COW-DUNG FOR BIOGAS PRODUCTION.
- Authors
-
-
Ochuko Mary Ojo
1Department of Civil and Environmental Engineering, the Federal University of Technology, Akure, PMB 704, Ondo State, Nigeria
-
J O Babatola
ATODATECH LLC, 742 Locust St, #301, Pasadena, CA, USA 91101.
-
A A Adesina
3Department of Mechanical Engineering, the Federal University of Technology, Akure, PMB 704, Ondo State, Nigeria
-
A O Akinola
1. Department of Mechanical Engineering, The Federal University of Technology Akure, Ondo State. Nigeria.
-
Olurinde Lafe
Centre for Renewable Energy, the Federal University of Technology, Akure, PMB 704, Ondo State, Nigeria
-
- Keywords:
- synergistic effect, water hyacinth, cow-dung, co-digestion, biogas production
- Abstract
-
The synergistic effect of co-digesting water hyacinth (WH) with cow-dung (CD) for optimum biogas production was evaluated. Different mix ratios of WH to CD were digested in a laboratory scale anaerobic digester over a retention time of 40 days. The volume of biogas produced was determined using water displacement method. The ultimate biogas yield and synergy factors for all the mixes were calculated. The third order polynomial curve for the different mixes had a R2 value of 0.9834 which is quite significant. The curve also showed that the highest ultimate biogas yield of 141.72 L was produced by 2 WH: 8 CD and impressively makes it the best CD-aided WH digestion mix. The highest synergy factor of 1.31 was observed for 2 WH: 8 CD which collaborates the fact that the best mix of CD-aided WH digestion in terms of biogas yield is 2 WH: 8 CD.
- References
- Downloads
- Published
- 2019-04-29
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- O. O. Olubanjo, A. E. Alade, Development of a Low Cost Greenhouse and Drip Hydroponic Structure for Vegetable Production in South-West Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 1 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- O. A. Dahunsi, M. O. Adeoti, O. O. Awopetu, F. O. Aramide, O. O. Alabi, A. S. Abdulkareem, Characterization of Saman-Burkono (Nigeria) Graphite for Crucible Production , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 1 (2019): FUTA Journal of Engineering and Engineering Technology
- I O OLADELE, O O DARAMOLA, A M OKORO, J A OMOTOYINBO, EVALUATION OF THE EFFECT OF MERCERIZED WHITE CHICKEN FEATHER FIBRES ON THE MECHANICAL , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 1 (2018): FUTA Journal of Engineering and Engineering Technology
- Kayode Francis Akingbade, DEVELOPMENT OF CHEMICAL PROPORTION FORMULATION MODEL FOR QUALITY CONTROL IN FLEXIBLE POLYURETHANE FOAM PRODUCTION , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 2 (2018): FUTA Journal of Engineering and Engineering Technology
- P B Mogaji, DEVELOPMENT OF AN IMPROVED CIRCULAR SAWING MACHINE , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 2 (2018): FUTA Journal of Engineering and Engineering Technology
- K. F. Akingbade, Development of Chemical Proportion Formulation Model for Quality Control in Flexible Polyurethane Foam Production , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 2 (2017): FUTA Journal of Engineering and Engineering Technology
- O. O. Awopetu, Effect of Rake Face Reinforcement on Cutting Tool Life of Cemented Carbide Tools during Turning of a-Titanium Alloy , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 1 (2017): FUTA Journal of Engineering and Engineering Technology
- D. T. Oloruntoba, S. O. Seidu, Effect of Mill Scale Particulate in Sand Mould on the Microstructure and Mechanical Properties of Cast 6063 Aluminium Alloys , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 8 No. 2 (2014): FUTA Journal of Engineering and Engineering Technology
- O. A. Adetola, O. J. Olukunle, T. L. Aremu, Investigation of The Effects of Yield On Selected Physical Properties of Cassava Tubers , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 10 No. 2 (2016): FUTA Journal of Engineering and Engineering Technology
- O.O. Ojo,, B.V. Eyiowuawi,, J.F. Akinfolarin,, MECHANICAL AND MORPHOLOGICAL FEATURES OF MICROWAVE HYBRID HEATING-INDUCED WELDING OF SS304 STAINLESS STEEL WITH COKE AS A SUSCEPTOR , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 9 No. 2 (2015): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.