APPRAISAL OF RELATED RISKS WITH LOCALLY MADE BLOCK MAKING MACHINE: A MULTI-SITE CASE STUDY OF NIGERIA BLOCK MAKING INDUSTRY
- Authors
-
-
O. Hezekiah Adeyemi
Department of Mechanical Engineering, Olabisi Onabanjo University, Nigeria
-
B Julius Olorunfemi,
Departments of Mechanical, Federal University Oye Ekiti, Ekiti State,
-
Olasunkanmi O Akinyemi
Departments of Mechanical, Federal University Oye Ekiti, Ekiti State, Nigeria
-
- Keywords:
- Hazard, Safety, Operators, Workers, Block, Machine, industry
- Abstract
-
Non-movement accidents usually arise from the use of machinery and it accounted for more than 10% of all accidents reported yearly. This study evaluated the common risks related to using locally made Block Making Machine (BMM) in 55 block making factories (BMF) located in the Southwest, Nigeria. The objective was to measure the level of exposures of workers to the machine related hazards. Questionnaire, involving 170 workers, and observation methods were used to obtain the safety conditions attached to operating the machines. The hazards prevention program checked by Safety Professionals (SaPro) included machine guarding, environmental hazards control and the use of Personal Protective Equipment (PPE) among others. Non-parametric Chi-Square tests and the independent sample t-test at p<0.05 were used to analyze the data. More than 87% of the total workers suffered injury on the job. Fingers, legs and low-back injuries were mostly reported by 80%, 68.5% and 63.3% workers respectively. Unguarded machinery (78.6%), awkward postures (75%), manual lifting (67%) and carelessness (60%) were the reported risk factors. The Chi-Square test showed that there was significant relationship between the ratings of the operators and the SaPro, on poor machine guarding, access to machine control and environmental control (Chi Square (272) = 8.741E2a , p = .000). The study asserted a need for a redesign of the locally made block making machine for inclusion of safety elements to enhance safety using the machine.
- References
- Downloads
- Published
- 2019-04-28
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- P B Mogaji, DEVELOPMENT OF AN IMPROVED CIRCULAR SAWING MACHINE , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 2 (2018): FUTA Journal of Engineering and Engineering Technology
- O. Z. Ayodeji, A. A. Adegun, S. A. Anjorin, DEVELOPMENT AND PERFORMANCE EVALUATION OF A SMALL-SCALE GROUNDNUT SHELLING MACHINE , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 2 (2021): FUTA Journal of Engineering and Engineering Technology
- H. A. Owolabi, B. V. Omidiji, A. O. Oke, A. T. Morakinyo, Development of a Small-Scale Motorized Dough Kneading Machine , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 2 (2017): FUTA Journal of Engineering and Engineering Technology
- A D Dada, BRIDGING RESEARCH-INDUSTRY DIVIDE IN FOOD AND BEVERAGE ENTERPRISES: EMPIRICAL EVIDENCE FROM SOUTHWESTERN NIGERIA , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 1 (2018): FUTA Journal of Engineering and Engineering Technology
- A. E. Owoputi, Issues in Safety and Security in Maritime Transportation, Port and Marine Environment , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 8 No. 2 (2014): FUTA Journal of Engineering and Engineering Technology
- M. K. Adeyeri, Proposition of Agent-based Preventive Maintenance Algorithm for Hammer Mill Machine Upkeep , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 10 No. 1 (2016): FUTA Journal of Engineering and Engineering Technology
- S. O. Osuji, P. N. Ogbeifun, Strength Properties of Stabilised Laterite as Replacement of Sand in Sandcrete Block Production , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 9 No. 2 (2015): FUTA Journal of Engineering and Engineering Technology
- N. G. Olaiya, P. K. Oke, P. B. Mogaji, Development of A Multipurpose Mix-Sieving Machine , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 1 (2019): FUTA Journal of Engineering and Engineering Technology
- T. B. Afeni, A. I. Lawal, S. J. Omosayin, Evaluation of Alluvial Ore Reserve in an Abandoned Consolidated Tin Mine, Bukuru- Jos Plateau State , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 9 No. 2 (2015): FUTA Journal of Engineering and Engineering Technology
- J. O. Ojediran, J. T. Fasinmirin, O. P. Owa, Development and Performance Evaluation of an Indigenous Fish Feed Palletizing Machine , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 2 (2017): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.