DEVELOPMENT OF A LOW COST MICROCONTROLLER - BASED HAEMOGLOBIN METER
- Authors
-
-
K D Adedayo
Department of Physics, Federal University of Technology, P. M. B.704, Akure, Ondo State, Nigeria.
-
T Ewetumo
Department of Physics, Federal University of Technology, P. M. B.704, Akure, Ondo State, Nigeria.
-
I Konwea
Department of Physics, Federal University of Technology, P. M. B.704, Akure, Ondo State, Nigeria.
-
T Ewetumo
Department of Physics, Federal University of Technology, P. M. B.704, Akure, Ondo State, Nigeria.
-
- Keywords:
- Keywords: Haemoglobin, Wavelength, Blood, Light Emitting Diode (LED)
- Abstract
-
This work looked at the determination of haemoglobin level in the blood using haemoglobin meter; an instrument for determining the absorbance value of haemoglobin in a sample of blood in g/dl.The haemoglobin meter was developed using light emitting diode (LEDs), a phototransistor, operational amplifiers, microcontroller (arduino board), liquid crystal display and a dark compartment. Samples of blood were smeared on a slide that was fixed between the LED and, phototransistor in the dark compartment. The LED emits radiation of visible light that pass through the blood sample which is detected by the phototransistor and is sent to the amplifier that amplifies the signal to a magnitude that can be picked up by the analog to digital converter (ADC) on the arduino board. The digital signal is then programmed by the microcontroller unit and the value is displayed on the liquid crystal display. The meter was calibrated against a standard (SH 120-1) and was examined for the accuracy of haemoglobin level. The developed system performed favourably well with the standard with a correlation value of0.98 at a percentage of 0.01% and the resolution is 0.001 g/dl.
- References
- Downloads
- Published
- 2019-04-28
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- B. O. Akinnuli, S. P Ayodeji, S. O. Abadariki, J. O. Fasan, Design, Fabrication and Performance Evaluation of a Reciprocating Cocoa Pod Breaking Machine , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 8 No. 1 (2014): FUTA Journal of Engineering and Engineering Technology
- Robert Oluwayimika Abolade, Oluwaseun Olayinka Tooki, David Oluwagbemiga Aborisade, REVIEW ARTICLE ON THE MITIGATION OF FOUR WAVE MIXING IN OPTICAL COMMUNICATION SYSTEM , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 1 (2021): FUTA Journal of Engineering and Engineering Technology
- S. O. Osuji, K. A. Ezekiel, E. O. Kenvin, Effect of Coarse Aggregate Type on the Modulus of Elasticity of Concrete , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 9 No. 1 (2015): FUTA Journal of Engineering and Engineering Technology
- J. T. Fasinmirin, Hydraulic and Compaction Characteristics of Soils in Grazed Land of Akure, Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 9 No. 1 (2015): FUTA Journal of Engineering and Engineering Technology
- T. O. Awodola, Dynamic Behaviour Under Moving Masses of Prestressed and Elastically Supported Plates Resting on Winkler Foundation , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 9 No. 1 (2015): FUTA Journal of Engineering and Engineering Technology
- E. C. Umeh, A. F. Isiaka, Analysis of the Short Fall in Production Target and Specific Cost of Unit Operations in National Iron Ore Mining Company NIOMCO, Itakpe. , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 8 No. 2 (2014): FUTA Journal of Engineering and Engineering Technology
- D. T. Oloruntoba, S. O. Seidu, Effect of Mill Scale Particulate in Sand Mould on the Microstructure and Mechanical Properties of Cast 6063 Aluminium Alloys , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 8 No. 2 (2014): FUTA Journal of Engineering and Engineering Technology
- A. P. Olalusi, Comparison of Selected Engineering Properties of Two Species of Cocoyam Essential for Handling of the Tubers , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 8 No. 2 (2014): FUTA Journal of Engineering and Engineering Technology
- A. O. Melodi, B. O. Akinloye, Transmission Capacity Enhancement for Nigerian Power Transmission Grid using TCSC and UPFC , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 8 No. 2 (2014): FUTA Journal of Engineering and Engineering Technology
- H. A. Owolabi, B. V. Omidiji, O. C. Falade, Optimization of Poultry Feeds Production Using Linear Programming Technique , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 9 No. 1 (2015): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.