CHARACTERIZATION OF DIFFERENT CASSAVA EFFLUENTS AND EVALUATION OF PROCESSOR ON-SITE HANDLING TECHNIQUES IN OGUN STATE, NIGERIA
- Authors
-
-
N S Lawal
Department of Agricultural Engineering, College of Engineering and Environmental Studies
-
A A Babalola
Department of Agricultural Engineering, College of Engineering and Environmental Studies, Olabisi Onabanjo University, Ogun State Nigeria.
-
O O Adama
Department of Agricultural Engineering, College of Engineering and Environmental Studies, Olabisi Onabanjo University, Ogun State Nigeria.
-
A O Sosanya
Department of Agricultural Engineering, College of Engineering and Environmental Studies, Olabisi Onabanjo University, Ogun State Nigeria.
-
A A Adebayo
Department of Agricultural Engineering, College of Engineering and Environmental Studies, Olabisi Onabanjo University, Ogun State Nigeria.
-
- Keywords:
- Cassava, wastewater, sustainability, environmental risk.
- Abstract
-
Cassava effluent was characterized with the aim of examining the current on-site management techniques among local processors for technological and regulatory improvements. Structured questionnaires were administered in sixty randomly selected processing clusters with different processing capacities to obtain data on the water consumption pattern, effluent output and quality, processing techniques and effluent management. The twenty-three physico-chemical parameters (pH (3.85), Oil and grease (0.386 mg/l), Electrical Conductivity (4.23 µmhos/cm), Biological oxygen demand (1889 mg/l), Total dissolved solids (3240 mg/l), Chemical oxygen demand (752.7 mg/l) Total suspended solids (9.28 mg/l), Bicarbonate (181.6 mg/l), Carbonate (387 mg/l), Sodium (1579.20 mg/l), Total nitrogen (0.86 mg/l), Potassium (1512.49 mg/l), Total Phosphate (300.41 mg/l), Calcium (35.4 mg/l), Magnesium (188.93 mg/l), Lead (59.39 mg/l), Cadmium (Not Detected), Chromium (0.28 mg/l), Iron (3.25 mg/l), Sulphate (17.75 mg/l), Turbidity (7620.96 NTU), Hydrogen Cyanide (678.50 mg/l) and Total Coliform count (2400 cfu/100ml)) analysed were mostly beyond permissible limits prescribed by regulating authorities. Wet fufu paste was the dominant product (73%) and generates the highest volume of wastewater (5-8 liters/tonne of fresh cassava root processed), while gari and fermented cassava flour (lafun) were 21% and 6% respectively. Processing water was predominantly sourced from boreholes (52%); 31% use near by stream water while 16% and 1% rely on water from deep wells and pipe-born water, respectively. On-site effluent handling techniques includes: direct disposal on land (50%), disposal in open drains (37%) and nearby streams (13%). The unwholesome effluent disposal techniques is largely due to the low level of education and processing technology adopted. Precautionary measures and strict regulations are urgently needed to prevent further environmental risk and degradation. Finally, alternative use of treated effluent for crop irrigation should be investigated and promoted to enhance agricultural productivity and economic sustainability among local processors
- References
- Downloads
- Published
- 2019-04-28
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- W. A. Raheem, A. O. Ajayeoba, K. A. Adebiyi, O. R. Oyetunji, O. A. Ayeyemi, Ergonomic Evaluation of Base Transceiver Station Maintenance Personnel in Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 1 (2019): FUTA Journal of Engineering and Engineering Technology
- A. S. Oyerinde, EFFECT OF DRYING RATE AND MOISTURE REMOVAL ON THE DRYING PROPERTIES OF GROUND AND FERMENTED CASSAVA MASH ("GARI") , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 1 (2021): FUTA Journal of Engineering and Engineering Technology
- J.A. Ojumu,, EFFECT OF SYNTHESIZED SILVER NANOPARTICLES FROM ALOE VERA PLANT LEAF EXTRACT ON CORROSION BEHAVIOUR OF API 5L IN 0.5M OF H2SO4 , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 2 (2019): FUTA Journal of Engineering and Engineering Technology
- M. M. Melodi, O. S. Adekinya, Assessment of Cost Effectiveness of Borehole Drilling in Oyo State, Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 10 No. 1 (2016): FUTA Journal of Engineering and Engineering Technology
- I. A. Oke, A. O. Obijole, E. A. Adekunbi, J. O. Babajide, M. D. Idi, T. A. Aladesanmi, THERMAL PROPERTY OF CARBON RESIN ELECTRODES DEVELOPED FOR ELECTROCHEMICAL TREATMENT OF WATER AND WASTEWATERS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 1 (2021): FUTA Journal of Engineering and Engineering Technology
- T. S. Mogaji, A. Akinsade, M. A. Akintunde, Pyrolysis of Sugarcane Bagasse for Bio-Oil Production , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 2 (2019): FUTA Journal of Engineering and Engineering Technology
- J. Isa, M. A. Aderotoye, Effect of moisture content on the physical and aerodynamics properties of cashew nut , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 2 (2017): FUTA Journal of Engineering and Engineering Technology
- A. E. Owoputi, Issues in Safety and Security in Maritime Transportation, Port and Marine Environment , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 8 No. 2 (2014): FUTA Journal of Engineering and Engineering Technology
- A. Fadeyibi, Z. D. Osunde, M. G. Visa, A. A. Okunola, Investigation into properties of starch-based nanocomposite materials for fruits and vegetables packaging - A review , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 1 (2017): FUTA Journal of Engineering and Engineering Technology
- P B Mogaji, DEVELOPMENT OF AN IMPROVED CIRCULAR SAWING MACHINE , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 2 (2018): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.