Soil Quality Analysis for Dumpsite Environment in a University Community in Nigeria
- Authors
-
-
C. O. Akinbile
Department of Agricultural & Environmental Engineering, Federal University of Technology, Akure, Nigeria
-
F. O. Ajibade
Department of Civil & Environmental Engineering, Federal University of Technology, Akure, Nigeria
-
O. Ofuafo
Department of Agricultural & Environmental Engineering, Federal University of Technology, Akure, Nigeria
-
- Keywords:
- Array, Array, Array, Array, Array, Array
- Abstract
-
Physicochemical analyses were carried out on soil samples from four different waste dumpsites in the Federal University of Technology Akure (FUTA), Nigeria to ascertain the effects of the refuse dumpsites on soil and groundwater qualities. Dumpsite locations are Physics Laboratory (PHY), Post Graduate Hostel (PG), School of Earth and Mineral Science (SEMS) and Staff Quarters (STQ). Soil samples collected at distances 0 (dumpsite), 10 and 20 m intervals away from the dumpsite were analyzed and at depths 10, 20 and 30 cm. Parameters determined include pH, Electrical Conductivity (EC), Magnesium (Mg), Calcium (Ca), Sodium (Na), Phosphorus (P), Nitrogen (N), Potassium (K), Organic Carbon (OC), Organic Matter (OM) and heavy metals such as Copper (Cu) and Lead (Pb) and subjected to relevant statistical analysis. Most of the parameters analyzed indicated pollution and were below the Food and Agricultural Organization (FAO) limits. P and Mg concentrations ranged from 1.19 to 1.25mg/kg and 3.17 to 13.61mg/kg respectively which indicated pollution. Out of heavy metals analyzed, Cu was 1.75mg/kg and Pb was not detected. Statistical analysis indicated significant differences at 95% level. The result showed that the soil samples were mildly polluted and therefore not suitable for crop production.
- Author Biography
- References
- Downloads
- Published
- 2019-05-03
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- S. T. Olowolafe, C. M. Ikumapayi, S. L. Akingbonmire, A. A. Olododo, J. A. Ajayi, INFRA-LIGHTWEIGHT CONCRETE: A COMPREHENSIVE REVIEW OF STRUCTURAL AND THERMAL PERFORMANCE WITH SUSTAINABLE AGGREGATES , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 20 No. Special (2026): FUTA JEET: Special Issue on Innovative Solutions for Sustainable Living and Environmental Challenges: Engineering Perspectives
- Adewuyi, Gideon Akinyemi, Daso, Akindele Wellington, Oke, Peter Kayode, INVESTIGATION AND CHARACTERIZATION OF ELEMENTAL COMPOSITION OF SOLAR PANEL , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 18 No. 2 (2024): FUTA Journal of Engineering and Engineering Technology
- Oyeleye, M. O, Melodi, A. O. , MODELING OF EFFICACIOUS LIGHTNING PROTECTION SCHEME ON NIGERIAN 11-132 kV SUBSTATIONS USING CONE OF PROTECTION METHODS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 17 No. 1 (2023): FUTA Journal of Engineering and Engineering Technology
- O. A. Agbolade, EVALUATING LORAWAN ADAPTIVE DATA RATE EFFECTIVENESS IN HETEROGENOUS SMART FARMING CONDITIONS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 20 No. Special (2026): FUTA JEET: Special Issue on Innovative Solutions for Sustainable Living and Environmental Challenges: Engineering Perspectives
- S. O. Osuji, P. N. Ogbeifun, Strength Properties of Stabilised Laterite as Replacement of Sand in Sandcrete Block Production , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 9 No. 2 (2015): FUTA Journal of Engineering and Engineering Technology
- H. A. Owolabi, B. V. Omidiji, O. C. Falade, Optimization of Poultry Feeds Production Using Linear Programming Technique , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 9 No. 1 (2015): FUTA Journal of Engineering and Engineering Technology
- Adekoya A. A, Adelabu, O. S. , Kolawole, F. O., DESIGN OF A DUAL DELTA FUSED DEPOSITION MODELLING 3D PRINTER FOR STUDIO CERAMICS PRODUCTION IN NIGERIA , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 1 (2025): FUTA Journal of Engineering and Engineering Technology
- Olabinjo, O. O., , Olusola, G. T. , Sama, M. O., EVALUATION OF PHYSICAL, CHEMICAL AND MICROBIAL PROPERTIES OF DATE FRUIT SEEDS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 18 No. 1 (2024): FUTA Journal of Engineering and Engineering Technology
- Tasiu Ashiru Sulaiman, Ibrahim Aliyu, Yusuf Yau, Ibrahim Bello, ASSESSMENT OF GROUNDNUT SHELL ASH AND SAWDUST ASH AS PARTIAL REPLACEMENT OF CEMENT IN CONCRETE , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 2 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- Alfred, V. A, Saliu, M. A, Omoegun, S.O. , Odeyemi, O. Y. , ASSESSMENT OF OXIDE PROPERTIES OF CLAY DEPOSITS FROM ANAMBRA GEOLOGICAL BASIN FOR THEIR SUITABILITY AS CERAMIC RAW MATERIALS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 17 No. 1 (2023): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.