The Effects of Drying Temperature on the Physicochemical Properties of Ogbono (lrvingia Gabonensis)
- Authors
-
-
J. A.V. Famurewa
Department of Food Science and Technology Federal University of Technology, Akure, Ondo State, Nigeria
-
E. T. Faboya
Department of Food Science and Technology, Rufus Giwa Polytechnic Owo, Ondo State, Nigeria
-
- Keywords:
- Array, Array, Array, Array, Array
- Abstract
-
The kernel seed flour of Ogbono (Irvingia gabonensis) was screened to test for the effects of drying temperatures on its physicochemical properties in order to evaluate its final qualities. Sorted and cleaned 'Ogbono' kernel seeds were splitted into two equal halves for uniform drying, weighed and dried at 50, 60 and 70°C. Weights of the samples were monitored at interval of one hour until constant weights were achieved. Analyses of the flour samples were carried out using analytical grade reagents. Proximate composition of the samples showed no significant difference at (p< 0.05) and ranged from 3.5 to 4.0, 1.99 to 3.24, 52.49 to 56.73, 1.86 to 2.62 and 33.86 to 38.71 for moisture content,protein, crude fat, total ash and carbohydrate respectively, this implies that Ogbono kernel seeds can be dried at any temperature within 50 to 70 °C without any appreciable loss of proximate values. The trend of the results showed decrease in the values of fat content but ash and carbohydrate content increase with increase in drying temperatures, low fat diet is recommended for both young and elderly people. Higher values were also recorded for mineral composition of the sample dried at 70 °C; 7.80, 194, 10.5 and 29.80/or Na, K, Ca and Fe respectively. The same sample also possessed relatively highest bulk density (0.60 g/cm3) which is important in relation to packaging efficiency. However sample dried at 50 °C is more viscous. Water and oil absorption capacities of the samples also decreased with increase in drying temperature which implies that more quantity will be needed when used as a thickener in food formulation for samples dried at higher air- drying temperatures. Drying temperature o/70 °C was therefore recommended to produce Ogbono flour of high chemical qualities.
- References
- Downloads
- Published
- 2019-05-04
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- AWOPETU, O. O, OWOYEMI, J. M, BABATUNDE, T. P. , OJO, O. T., DEVELOPMENT OF A TRANSFORMABLE FURNITURE SYSTEM: FROM SHELVING UNIT TO FUNCTIONAL TABLETOP , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 18 No. 1 (2024): FUTA Journal of Engineering and Engineering Technology
- J. O. Amigun, Seismic Inverted Acoustic Impedance for Lithofacies Discrimination and Reservoir Fluids Prediction: A Case of ‘Ovi’ Field, Niger Delta , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 2 (2019): FUTA Journal of Engineering and Engineering Technology
- Dafiewhare, O, Ijagbemi, C. O, Ologunwa, T. P, Alabi, O. T, Ijagbemi, A. O, PRODUCTION AND EVALUATION OF BIOMASS BRIQUETTES FROM PALM KERNEL SHELL AND COCONUT HUSK , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 2 (2025): FUTA Journal of Engineering and Engineering Technology
- Adeyemo, A. J. , LAND USE EFFECTS ON SOIL CARBON AND NITROGEN ENZYMES IN A HUMID TROPICAL ECOSYSTEMS OF SOUTH WESTERN NIGERIA , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 17 No. 2 (2023): FUTA Journal of Engineering and Engineering Technology
- J T Fasinmirin, D O Rapheal, J Lazarus, SOIL CHARCTERIZATION AND MAIZE (Zea mays L.) EVAPOTRANSPIRATION (ETc) IN OMU-ARAN HUMID GEOLOGICAL ZONE OF NIGERIA , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 1 (2018): FUTA Journal of Engineering and Engineering Technology
- O. A. Dahunsi, M. O. Adeoti, O. O. Awopetu, F. O. Aramide, O. O. Alabi, A. S. Abdulkareem, Characterization of Saman-Burkono (Nigeria) Graphite for Crucible Production , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 1 (2019): FUTA Journal of Engineering and Engineering Technology
- George, U. D, Akpan, M. G, Onwe, D. N, MACHINE LEARNING CLASSIFIER FOR DALIUM GUINEENSE FRUIT USING ITS PHYSICAL PROPERTIES , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 17 No. 1 (2023): FUTA Journal of Engineering and Engineering Technology
- C. O. Akinbile, F. O. Ajibade, O. Ofuafo, Soil Quality Analysis for Dumpsite Environment in a University Community in Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 10 No. 2 (2016): FUTA Journal of Engineering and Engineering Technology
- R. K. Apalowo, J. A. Kehinde, E. O. Oyeleke, O. J. Owoloja, S. O. Famuyiwa, MACHINE LEARNING OPTIMIZATION OF UNDERFILL FLOW TIME IN FLIP-CHIP ENCAPSULATION OF BGA ASSEMBLIES , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 20 No. 1 (2026): FUTA Journal of Engineering and Engineering Technology
- Fayose, F, Arowolo, M, Olajide, A., Adewale, D, DESIGN AND PRELIMINARY TESTING OF A SMALL-SCALE CASHEW HARVESTER , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 17 No. 2 (2023): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.