Mechanical Wear Resistance and Water Absorption Properties of Particulate Palm Kernel Shell Reinforced Epoxy Composites for Automobile Application
- Authors
-
-
A. S. Taiwo
Department of Metallurgical and Materials Engineering, The Federal University of Technology, Akure, Ondo State, Nigeria
-
I. O. Oladele
Department of Metallurgical and Materials Engineering, The Federal University of Technology, Akure, Ondo State, Nigeria
-
O. O. Daramola
Department of Metallurgical and Materials Engineering, The Federal University of Technology, Akure, Ondo State, Nigeria
-
A. D. Akinwekomi
Department of Metallurgical and Materials Engineering, The Federal University of Technology, Akure, Ondo State, Nigeria
-
O. G. Agbabiaka
Department of Metallurgical and Materials Engineering, The Federal University of Technology, Akure, Ondo State, Nigeria
-
- Keywords:
- Array, Array, Array, Array, Array, Array, Array
- Abstract
-
This work investigates the effects of particulate palm kernel shell (PKS) on epoxy matrix for the development of composites that can be used as substitute to the conventional metallic bumpers in automobiles. The PKS was sourced from an oil plantation and washed thoroughly with water before sun dried. The dried PKS was pulverized using a laboratory ball mill and sieved into 45 µm particle sizes. Elemental composition of the PKS was determined using XRF. The PKS particulate was randomly dispersed in the epoxy resin to develop composite samples of varied weight contents. The developed samples were tested to determine their impact toughness, wear resistance, flexural, tensile and water absorption properties. The results showed that higher weight contents within 10 - 20 wt.% PKS reinforcement gave the best performance in most of the mechanical properties examined with the exception of tensile and flexural properties which were enhanced at 8 wt.%. Water absorption was noticed to increase as the PKS content increases from 2 - 20 wt.%.
- References
- Downloads
- Published
- 2019-05-14
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- Ijagbemi, C.O, Olabanji, O. M, Ashiru, A.R, Abdulmumuni, B, IJagbemi F.M, DEVELOPMENT OF ETHANOL GEL COOK STOVE , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 1 (2025): FUTA Journal of Engineering and Engineering Technology
- O P FAPETU, A O AKINOLA, L L LAJIDE, A B OSASONA, PHYSICOCHEMICAL CHARACTERISTICS STUDY OF OIL EXTRACTED FROM RAFFIA PALM SEED , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 1 (2018): FUTA Journal of Engineering and Engineering Technology
- D. T. Oloruntoba, S. O. Seidu, Effect of Mill Scale Particulate in Sand Mould on the Microstructure and Mechanical Properties of Cast 6063 Aluminium Alloys , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 8 No. 2 (2014): FUTA Journal of Engineering and Engineering Technology
- A. P. Olalusi, Comparison of Selected Engineering Properties of Two Species of Cocoyam Essential for Handling of the Tubers , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 8 No. 2 (2014): FUTA Journal of Engineering and Engineering Technology
- Akinola, A. O, Abdulkadir, M, Bello, E. I, Adedeji, S. Y., PRODUCTION AND CHARACTERIZATION OF BIODIESEL FROM MARULA (Sclerocarya birrea) SEED OIL , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 16 No. 2 (2022): FUTA Journal of Engineering and Engineering Technology
- FADUGBA O.G., EVALUATION OF STRENGTH AND LEACHING PROPERTIES OF SNAIL SHELL ASH (SSA) REMEDIATED PETROLEUM HYDROCARBON CONTAMINATED LATERITIC SOILS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 1 (2025): FUTA Journal of Engineering and Engineering Technology
- Mogaji, T. S, Fasasi, S. T, Ogundairo, A. O, Oluwagbemi, I. A, DESIGN AND SIMULATION OF A PICO HYDROELECTRIC TURBINE SYSTEM , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 16 No. 1 (2022): FUTA Journal of Engineering and Engineering Technology
- Ojo, O. O , Ajayi, B. O, FRACTURE BEHAVIOR AND MECHANICAL PERFORMANCE OF DISSIMILAR FRICTION STIR CLINCHED CU/AL JOINT , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 16 No. 1 (2022): FUTA Journal of Engineering and Engineering Technology
- A. S. Ogbiye, Lucia O. Agashua, Effects of concrete mixing fluid samples - fermented locust beans and sewage on the strength properties of self-healing concrete , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 1 (2019): FUTA Journal of Engineering and Engineering Technology
- Ojo, O. T, Mogaji, T. S, Adeyeri, M. K, Ayodeji, S. P, Fagbemi, T. N, DESIGN AND FINITE ELEMENT ANALYSIS OF AN INDUSTRIAL-BASED VEGETABLE LEAF WASHING MACHINE , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 16 No. 1 (2022): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.