Microwave Sintering and Characterisation of Magnesium Alloy AZ61/Carbon Nanotube Composites
- Authors
-
-
A. D. Akinwekomi
Department of Metallurgical and Materials Engineering, The Federal University of Technology, Akure, Ondo State, Nigeria
-
I. O. Oladele
Department of Metallurgical and Materials Engineering, The Federal University of Technology, Akure, Ondo State, Nigeria
-
A. Oyetunji
Department of Metallurgical and Materials Engineering, The Federal University of Technology, Akure, Ondo State, Nigeria
-
- Keywords:
- Array, Array, Array, Array
- Abstract
-
AZ61 magnesium alloy composites reinforced with 2 vol.% of carbon nanotubes (CNTs) were synthesized via the powder metallurgy and microwave (MW) sintering techniques. Using a mechanical alloying (MA) process, the CNTs were incorporated into the AZ61 matrix as the reinforcement phase within 15 hours. The milling medium consisted of steel balls with two different diameters to reduce the size of the AZ61 powder and homogeneously distribute the CNTs in the matrix. The CNTs were not damaged during the MA process as confirmed from the Raman spectra of the composite powder. MW sintering was completed in 10 minutes and the sintered samples had a porosity of ~6%. Further characterization showed that the monolithic sample exhibited 42 Hv, 110 MPa, and 136 MPa for microhardness, compressive yield strength and ultimate compressive strength, respectively. Significant improvements were observed in the properties of the composite sample, which amounted to increments of 68% in microhardness, and ~ 21% and ~56% in yield strength and ultimate compressive strength, respectively. The presence of CNTs in the matrix did not compromise the failure strain of the matrix.
- References
- Downloads
- Published
- 2019-05-14
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- Oluwatoyin Olaseinde, O. Ajanaku, O. M. Ojo, S. O. Seidu, COMPARATIVE STUDY OF THE REINFORCED STEEL BARS OBTAINED FROM A FAILED RESIDENTIAL BUILDING AND THE SHELVES , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 2 (2021): FUTA Journal of Engineering and Engineering Technology
- K. O. Oladosu, E. O. Olafimihan, K. A. Babatunde, B. Kareem, A. A. Mustapha, Investigation of Staged Air supply on Grate Combustion of Palm Kernel Shell Mixed with Selected additives (Al2O3 and CaO) , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 1 (2019): FUTA Journal of Engineering and Engineering Technology
- S. O. Obayopo, F. J. Banjoko, S. A. Balogun, H. B. Adedayo, Investigation into the Use of Blended Sunflower Oil and Superolein in Hydraulic Systems , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 1 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- Ijagbemi, C.O, Olabanji, O. M, Ashiru, A.R, Abdulmumuni, B, IJagbemi F.M, DEVELOPMENT OF ETHANOL GEL COOK STOVE , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 1 (2025): FUTA Journal of Engineering and Engineering Technology
- IDOWU Abimbola Samson , ADEWUYI B.O, FOLORUNSO D.O, AKINWEKOMI A. D., OPTIMUM INFLUENCE OF CHROMIUM AND COMBINE AUSTEMPERING-CRYOGENIC TREATMENTS ON PERFORMANCE OF DUCTILE IRON , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 1 (2025): FUTA Journal of Engineering and Engineering Technology
- P. B. Mogaji, T. E. Abioye, N. O. Ohuruogu, Development of Epoxy Resin Composite Reinforced With Cow Horn and Cassava Particles for Car Dashboard , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 1 (2017): FUTA Journal of Engineering and Engineering Technology
- T. S. Mogaji, A. Akinsade, M. A. Akintunde, Pyrolysis of Sugarcane Bagasse for Bio-Oil Production , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 2 (2019): FUTA Journal of Engineering and Engineering Technology
- O. A. Dahunsi, M. O. Adeoti, O. O. Awopetu, F. O. Aramide, O. O. Alabi, A. S. Abdulkareem, Characterization of Saman-Burkono (Nigeria) Graphite for Crucible Production , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 1 (2019): FUTA Journal of Engineering and Engineering Technology
- Adewuyi, Gideon Akinyemi, Daso, Akindele Wellington, Oke, Peter Kayode, INVESTIGATION AND CHARACTERIZATION OF ELEMENTAL COMPOSITION OF SOLAR PANEL , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 18 No. 2 (2024): FUTA Journal of Engineering and Engineering Technology
- I. O. Oladele, O. G. Agbabiaka, O. S. Akinola, H. K. Talabi, Development of Sponge Fiber and Particulate Palm Kernel Shell Ash Reinforced Polypropylene Hybrid Composites , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 10 No. 2 (2016): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.