Investigation of Multilevel Transmission for SI-Plastic Optical Fibre (POF) Channel: PAM and OFDM
- Authors
-
-
W. O. Apena
-
I. Osahon
-
W. O. Popoola
-
- Keywords:
- Array, Array, Array, Array
- Abstract
-
This research studied the choice of Step-Index (SI)Plastic Optical Fibre (POF) as a vital channel for short distance Multilevel (PAM & OFDM) transmission scheme in optical communication system (OCS). This employed initial knowledge on digital modulation to select promised modulation techniques (QPSK-OFDM, 16QAM-OFDM, 2-PAM, and 4-PAM) for POF channel. The controlled experiment was setup in the laboratory using transmitter (LED-L10762, 70MHzand Bias T-ZFBT-4R2GW) and receiver (Photo-receiver) through POF channel length variation (45cm, 30m and 60m) to determine the frequency response (back-to-back) and data rate (DR) performance respectively. Itrevealed disparities in bit error rate (BER) and data rate (DR) performances with respect to distance variation (30m and 60m POF channel). In summary, the bit error rates (BERs) for 30m POF for the chosen modulation techniques are lower compared to 60m POF which shows significance of modulation techniques with respect to POF channel distance. The research shows that POF could be an effective channel for short distance network such as Local Area Network (LAN) and Campus Area Network (CAN) application.
- References
- Downloads
- Published
- 2019-11-17
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- S. S. Yaru, POLLUTION OF VEHICULAR EMISSION ANALYSIS AT FEDERAL UNIVERSITY OF TECHNOLOGY AKURE NORTH GATE , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 1 (2021): FUTA Journal of Engineering and Engineering Technology
- A. S. Oyerinde, EFFECT OF DRYING RATE AND MOISTURE REMOVAL ON THE DRYING PROPERTIES OF GROUND AND FERMENTED CASSAVA MASH ("GARI") , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 1 (2021): FUTA Journal of Engineering and Engineering Technology
- SOYOYE Babatunde Oluwamayokun, FALAYI Folayan Richard, OGUNJIMI Jumoke Omowumi, OLORUNFEMI Emmanuel Olasunkanmi, DEVELOPMENT AND PERFORMANCE EVALUATION OF A MOTORIZED BATTERY-POWERED SPRAYER , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 1 (2025): FUTA Journal of Engineering and Engineering Technology
- D. T. Oloruntoba, S. O. Seidu, Effect of Mill Scale Particulate in Sand Mould on the Microstructure and Mechanical Properties of Cast 6063 Aluminium Alloys , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 8 No. 2 (2014): FUTA Journal of Engineering and Engineering Technology
- Kayode Francis Akingbade, DEVELOPMENT OF CHEMICAL PROPORTION FORMULATION MODEL FOR QUALITY CONTROL IN FLEXIBLE POLYURETHANE FOAM PRODUCTION , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 2 (2018): FUTA Journal of Engineering and Engineering Technology
- F. M. Dahunsi, S. O. Oluponna, Analysis of Energy Usage Pattern of a Nigerian University Digital Resource Center (DRC):: FUTA DRC as a Case Study , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 2 (2019): FUTA Journal of Engineering and Engineering Technology
- P. B. Mogaji, O. A. Raimi, Determination of Optimum Parameters for Drilling Stainless Steel using Response Surface Methodology (RSM) , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 10 No. 1 (2016): FUTA Journal of Engineering and Engineering Technology
- R. K. Apalowo, J. A. Kehinde, E. O. Oyeleke, O. J. Owoloja, S. O. Famuyiwa, MACHINE LEARNING OPTIMIZATION OF UNDERFILL FLOW TIME IN FLIP-CHIP ENCAPSULATION OF BGA ASSEMBLIES , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 20 No. 1 (2026): FUTA Journal of Engineering and Engineering Technology
- O. A. Awodele, Appraisal of Risk Identification and Response Techniques adopted on Building Projects in Rivers State, Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 10 No. 1 (2016): FUTA Journal of Engineering and Engineering Technology
- Adebayo Felix Owa, Abdulahi Olawale Adebayo, Olawale Olarewaju Ajibola, Oluwole Daniel Adigun, Sunday Gbenga Aborisade, Fisayo Adesina, Corrosion Behaviour of Low Carbon Steel in Sulphide Medium Using Thevetia Peruviana as Inhibitor , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 2 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
You may also start an advanced similarity search for this article.