Investigation of Multilevel Transmission for SI-Plastic Optical Fibre (POF) Channel: PAM and OFDM
- Authors
-
-
W. O. Apena
-
I. Osahon
-
W. O. Popoola
-
- Keywords:
- Array, Array, Array, Array
- Abstract
-
This research studied the choice of Step-Index (SI)Plastic Optical Fibre (POF) as a vital channel for short distance Multilevel (PAM & OFDM) transmission scheme in optical communication system (OCS). This employed initial knowledge on digital modulation to select promised modulation techniques (QPSK-OFDM, 16QAM-OFDM, 2-PAM, and 4-PAM) for POF channel. The controlled experiment was setup in the laboratory using transmitter (LED-L10762, 70MHzand Bias T-ZFBT-4R2GW) and receiver (Photo-receiver) through POF channel length variation (45cm, 30m and 60m) to determine the frequency response (back-to-back) and data rate (DR) performance respectively. Itrevealed disparities in bit error rate (BER) and data rate (DR) performances with respect to distance variation (30m and 60m POF channel). In summary, the bit error rates (BERs) for 30m POF for the chosen modulation techniques are lower compared to 60m POF which shows significance of modulation techniques with respect to POF channel distance. The research shows that POF could be an effective channel for short distance network such as Local Area Network (LAN) and Campus Area Network (CAN) application.
- References
- Downloads
- Published
- 2019-11-17
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- Abdalla Esmaeel, Sesan Peter Ayodeji, Diana Starovoytova, Jerry Ochola, ERGONOMIC RISK SIMULATION USING RAPID UPPER LIMB ASSESSMENT TOOL FOR THE SITTING POSTURE OF GARMENTS WORKERS: A CASE OF RIVATEX EAST AFRICA LIMITED, ELDORET, KENYA , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 20 No. Special (2026): FUTA JEET: Special Issue on Innovative Solutions for Sustainable Living and Environmental Challenges: Engineering Perspectives
- S. O. Osuji, P. N. Ogbeifun, Strength Properties of Stabilised Laterite as Replacement of Sand in Sandcrete Block Production , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 9 No. 2 (2015): FUTA Journal of Engineering and Engineering Technology
- E. O. Ajaka, O. E. Abiodun, Determining The Metal Contents of Leach Liqour from Ihietutu Lead and Zinc Ore, Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 1 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- Akinola, A. O, Yaya-Bankole H. J , EMPIRICAL DETERMINATION OF AIR CONDITIOING INSTALLATION AND MAINTENANCE CHALLENGES IN LAGOS STATE, NIGERIA , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 1 (2025): FUTA Journal of Engineering and Engineering Technology
- Amosu, C.O., CONTROLLING MINE WATER IN GOLDEN GIRL QUARRY IN IKPESHI, EDO STATE, NIGERIA , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 18 No. 1 (2024): FUTA Journal of Engineering and Engineering Technology
- H. A. Owolabi, B. V. Omidiji, O. C. Falade, Optimization of Poultry Feeds Production Using Linear Programming Technique , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 9 No. 1 (2015): FUTA Journal of Engineering and Engineering Technology
- A. A. Akinlabi, A. P. Faluyi, J. M. Iberedem, F. M. Dahunsi, INTERNLY: A MOBILE PLATFORM FOR CONNECTING NIGERIAN STUDENTS TO INTERNSHIP OPPORTUNITIES , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 20 No. Special (2026): FUTA JEET: Special Issue on Innovative Solutions for Sustainable Living and Environmental Challenges: Engineering Perspectives
- I O OLADELE, O O DARAMOLA, A M OKORO, J A OMOTOYINBO, EVALUATION OF THE EFFECT OF MERCERIZED WHITE CHICKEN FEATHER FIBRES ON THE MECHANICAL , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 1 (2018): FUTA Journal of Engineering and Engineering Technology
- M. M. Melodi, T. G. Onipede, Economic Appraisal of Some Selected Quarries Operation in Ondo State, Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 2 (2017): FUTA Journal of Engineering and Engineering Technology
- W. O. Apena, G. A. Oladunni, Comparative Analysis of Path Loss Prediction Models for Selected Rural Areas in Ondo State, Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 2 (2019): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.