A Modified Droop Controller for Micro-Grid Power Quality Improvement Using Artificial Fish Swarm Algorithm (AFSA)
- Authors
-
-
Abdulwahab J. Yusuf
Department of Electrical & Computer Engineering; Ahmadu Bello University, Zaria, Nigeria
-
A. A. Olaniyan
Department of Electrical/Electronic Engineering Technology; Auchi Polytechnic, Auchi, Nigeria
-
- Keywords:
- Array, Array, Array, Array
- Abstract
-
This paper presents a modiï¬ed droop controller for improving the power quality of micro-grid using Artiï¬cial Fish Swarm Algorithm (AFSA). This is necessary in order to reduce the frequency and voltage deviations that occur when the micro-grid changes from grid-connected to an autonomous mode or when the load changes. AFSA was used to optimally select and tune the droop controller gain parameters in order to achieve an improved response in the frequency and voltage outputs of the micro-grid in the course of islanding. The performance of the AFSA-based droop controller was compared with that of the genetic algorithm (GA) based droop controller using the values of frequency and voltage deviations as performance metrics. And from the results obtained, it was observed that the result obtained from the micro-grid when AFSA was used to optimize the droop controller outperforms that obtained when GA was used in terms of frequency and voltage by 0.213% and 1.0453% respectively. All modeling and analysis were implemented in MATLAB 2015b.
- References
- Downloads
- Published
- 2019-11-16
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- Oluseyi Orisadare, Ayodeji S. Olawore, Michael O. Ibiwoye, Eyitayo A. Ponle, Omolola T. Odeyemi, Opeyemi S. Kegbeyale, MECHANICAL AND MICROSTRUCTURAL PROPERTIES OF BRASS REINFORCED WITH COCONUT SHELL ASH POWDER , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 2 (2021): FUTA Journal of Engineering and Engineering Technology
- O. O. Omotayo, P. M. Omowaye, C. M. Ikumapayi, C. Arum, INFLUENCE OF BURNING TEMPERATURE ON RICE HUSK ASH MICROSTRUCTURE AND POZZOLANIC REACTIVITY , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 20 No. Special (2026): FUTA JEET: Special Issue on Innovative Solutions for Sustainable Living and Environmental Challenges: Engineering Perspectives
- M. A. Azeez, O. Oluwaseyi, A. A. Ajiboye, A. Iwayemi, Performance Evaluation of A Reverse Aodv And Aodv Routing Protocol Under Jellyfish Attacks in Mobile Ad Hoc Network , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 10 No. 1 (2016): FUTA Journal of Engineering and Engineering Technology
- A. D. Akinwekomi, I. O. Oladele, A. Oyetunji, Microwave Sintering and Characterisation of Magnesium Alloy AZ61/Carbon Nanotube Composites , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 1 (2019): FUTA Journal of Engineering and Engineering Technology
- Ojo, O.O, Babalola, W.O., Mohammed, T.I, IMPACT OF FRICTION STIR PROCESSING ON THE FUSION-WELDED AISI 304 STAINLESS STEEL JOINTS: MICROSTRUCTURE, MECHANICAL AND FRACTURE BEHAVIOURS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 2 (2025): FUTA Journal of Engineering and Engineering Technology
- Ojo Oluwole Timothy , 2Adeniji Toyosi Adelowokan, DEVELOPMENT OF A BIOMETRIC, FACIAL RECOGNITION AND AUTHENTICATION SYSTEM FOR CLASS ATTENDANCE MANAGEMENT , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 1 (2025): FUTA Journal of Engineering and Engineering Technology
- B. K. Adeoye, U. Nwitte-Eze, A. D. Adeniran, A QUANTITATIVE STUDY OF MICROMERITICS PROPERTIES OF CO-PROCESSED BINDER ON THE NUTRITIONAL AND MECHANICAL PROPERTIES OF EXTRUDED MEAT SNACKS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 20 No. Special (2026): FUTA JEET: Special Issue on Innovative Solutions for Sustainable Living and Environmental Challenges: Engineering Perspectives
- O.O. Ojo,, B.V. Eyiowuawi,, J.F. Akinfolarin,, MECHANICAL AND MORPHOLOGICAL FEATURES OF MICROWAVE HYBRID HEATING-INDUCED WELDING OF SS304 STAINLESS STEEL WITH COKE AS A SUSCEPTOR , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 9 No. 2 (2015): FUTA Journal of Engineering and Engineering Technology
- W. O. Apena, K. F. Akingbade, Modelling of Electric Power Subsystem for a Weather Balloon Microsatellite , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 1 (2017): FUTA Journal of Engineering and Engineering Technology
- D. T. Oloruntoba, S. O. Seidu, Effect of Mill Scale Particulate in Sand Mould on the Microstructure and Mechanical Properties of Cast 6063 Aluminium Alloys , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 8 No. 2 (2014): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.