A Modified Droop Controller for Micro-Grid Power Quality Improvement Using Artificial Fish Swarm Algorithm (AFSA)
- Authors
-
-
Abdulwahab J. Yusuf
Department of Electrical & Computer Engineering; Ahmadu Bello University, Zaria, Nigeria
-
A. A. Olaniyan
Department of Electrical/Electronic Engineering Technology; Auchi Polytechnic, Auchi, Nigeria
-
- Keywords:
- Array, Array, Array, Array
- Abstract
-
This paper presents a modiï¬ed droop controller for improving the power quality of micro-grid using Artiï¬cial Fish Swarm Algorithm (AFSA). This is necessary in order to reduce the frequency and voltage deviations that occur when the micro-grid changes from grid-connected to an autonomous mode or when the load changes. AFSA was used to optimally select and tune the droop controller gain parameters in order to achieve an improved response in the frequency and voltage outputs of the micro-grid in the course of islanding. The performance of the AFSA-based droop controller was compared with that of the genetic algorithm (GA) based droop controller using the values of frequency and voltage deviations as performance metrics. And from the results obtained, it was observed that the result obtained from the micro-grid when AFSA was used to optimize the droop controller outperforms that obtained when GA was used in terms of frequency and voltage by 0.213% and 1.0453% respectively. All modeling and analysis were implemented in MATLAB 2015b.
- References
- Downloads
- Published
- 2019-11-16
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- O.I. Adebisi, THE EFFECT OF COMBINED SERIES-SHUNT PASSIVE FILTER ON HARMONIC DISTORTION AND POWER LOSSES IN AN ELECTRICAL DISTRIBUTION NETWORK , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 20 No. Special (2026): FUTA JEET: Special Issue on Innovative Solutions for Sustainable Living and Environmental Challenges: Engineering Perspectives
- M. K. Adeyeri, Proposition of Agent-based Preventive Maintenance Algorithm for Hammer Mill Machine Upkeep , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 10 No. 1 (2016): FUTA Journal of Engineering and Engineering Technology
- Ogundele, O. J, Adebisi, O. I, Adejumobi, I. A, Amusa, K. A. , Alabi, A. A, POWER QUALITY ENHANCEMENT IN AN ELECTRICAL DISTRIBUTION NETWORK USING SHUNT PASSIVE FILTER , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 18 No. 1 (2024): FUTA Journal of Engineering and Engineering Technology
- J. J. Popoola, D. O. Akinfenwa, I. O. Animasahun, Assessment of Electromagnetic Radiation Effects and Safety Issues of GSM-900 and GSM-1800 Radio Frequencies – A Case Study of Akure, Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 9 No. 1 (2015): FUTA Journal of Engineering and Engineering Technology
- R. F. Falayi, P. A. Adeduntan, EFFECTS OF WOODASH AND SAWDUST ADMIXTURE ON ENGINEERING PROPERTIES OF BURNT LATERITE CLAY BRICKS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 20 No. Special (2026): FUTA JEET: Special Issue on Innovative Solutions for Sustainable Living and Environmental Challenges: Engineering Perspectives
- O. Hezekiah Adeyemi, B Julius Olorunfemi,, Olasunkanmi O Akinyemi, APPRAISAL OF RELATED RISKS WITH LOCALLY MADE BLOCK MAKING MACHINE: A MULTI-SITE CASE STUDY OF NIGERIA BLOCK MAKING INDUSTRY , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 2 (2018): FUTA Journal of Engineering and Engineering Technology
- LADI OGUNWOLU, Adeyanju Sosimi, Toheeb Salahudeen, A MULTI-OBJECTIVE RESOURCE-CONSTRAINED PROJECT SCHEDULING PROBLEM USING GENETIC ALGORITHM , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 1 (2018): FUTA Journal of Engineering and Engineering Technology
- K. F. Akingbade, Development of Chemical Proportion Formulation Model for Quality Control in Flexible Polyurethane Foam Production , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 2 (2017): FUTA Journal of Engineering and Engineering Technology
- Ayanshola, A.M., , Adidu, J.A, Iji, J.O., , Oladimeji, S.B, Sule, B.F, Salami, A.W. , Bilewu, S.O., ESTIMATING THE POTENTIAL FOR RAINWATER HARVESTING IN ILORIN, NORTH CENTRAL, NIGERIA , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 18 No. 1 (2024): FUTA Journal of Engineering and Engineering Technology
- C. M. Ikumapayi, COMPARATIVE ANALYSIS OF POLYMER CONCRETE FORMULATED FROM LOW-DENSITY POLYETHYLENE POLYMERS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 20 No. 1 (2026): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.