MECHANICAL PROPERTIES OF EPOXY MATRIX COMPOSITES REINFORCED WITH GARLIC PARTICLES
- Authors
-
-
O. O. Daramola
3Department of Metallurgical and Materials Engineering, Federal University of Technology, Akure, PMB 704, Nigeria
-
I. O. Oladele
Department of Metallurgical and Materials Engineering, Federal University of Technology, Akure, PMB 704, Nigeria
-
O. S. AKINTAYO
Department of Metallurgical and Materials Engineering, Federal University of Technology, Akure, PMB 704, Nigeria
-
- Keywords:
- Array, Array, Array, Array, Array
- Abstract
-
Epoxy resin with different weight fractions of submicron garlic particles were used to develop epoxy composites. Mechanical properties (tensile, flexural and impact) of the developed composites were characterized. The microstructure of tensile fractured surfaces was examined by Scanning Electron Microscope (SEM) in order to identify the relevant fracture modes involved. Results showed that the tensile strength, tensile modulus, flexural strength, flexural stiffness and impact strength was enhanced in the composites with the tensile strength, tensile modulus and impact strength experiencing peak values at 8 wt.% garlic loading before decreasing. Flexural strength and stiffness increased in a linear mode while elongation at break was found to reduce slightly in the composites when compared to the neat epoxy resin. Microstructure revealed the brittle nature of the neat epoxy. Individual particles with low degree of aggregation were observed in the composites with lower loading. However, particles agglomeration was observed in the highly filled composite (10 wt% garlic) resulting in the termination of the linear increase experienced in the tensile strength, tensile modulus and impact strength results. Overall, the test results demonstrate the competency of garlic particles to serve as a reliable, cost effective and efficient reinforcement material for the development of epoxy reinforced composites.
- References
- Downloads
- Published
- 2025-12-08
- Section
- Articles
- License
-
Copyright (c) 2021 FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY

This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- Adewuyi, Gideon Akinyemi, Daso, Akindele Wellington, Oke, Peter Kayode, INVESTIGATION AND CHARACTERIZATION OF ELEMENTAL COMPOSITION OF SOLAR PANEL , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 18 No. 2 (2024): FUTA Journal of Engineering and Engineering Technology
- T. S. Mogaji, A. Akinsade, M. A. Akintunde, Pyrolysis of Sugarcane Bagasse for Bio-Oil Production , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 2 (2019): FUTA Journal of Engineering and Engineering Technology
- O.O. Ojo,, B.V. Eyiowuawi,, J.F. Akinfolarin,, MECHANICAL AND MORPHOLOGICAL FEATURES OF MICROWAVE HYBRID HEATING-INDUCED WELDING OF SS304 STAINLESS STEEL WITH COKE AS A SUSCEPTOR , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 9 No. 2 (2015): FUTA Journal of Engineering and Engineering Technology
- Ojo, O.O., Eyiowuawi, B.V., Akinfolarin, J.F., MECHANICAL AND MORPHOLOGICAL FEATURES OF MICROWAVE HYBRID HEATING-INDUCED WELDING OF SS304 STAINLESS STEEL WITH COKE AS A SUSCEPTOR , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 2 (2025): FUTA Journal of Engineering and Engineering Technology
- IDOWU Abimbola Samson , ADEWUYI B.O, FOLORUNSO D.O, AKINWEKOMI A. D., OPTIMUM INFLUENCE OF CHROMIUM AND COMBINE AUSTEMPERING-CRYOGENIC TREATMENTS ON PERFORMANCE OF DUCTILE IRON , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 1 (2025): FUTA Journal of Engineering and Engineering Technology
- Talabi H. K. , GREEN SYNTHESIS AND CHARACTERIZATION OF COPPER NANOPARTICLES AS REINFORCEMENT IN EPOXY BASED COMPOSITE USING SPONDIAS MOMBIN LEAF EXTRACT , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 18 No. 2 (2024): FUTA Journal of Engineering and Engineering Technology
- Dafiewhare, O, Ijagbemi, C. O, Ologunwa, T. P, Alabi, O. T, Ijagbemi, A. O, PRODUCTION AND EVALUATION OF BIOMASS BRIQUETTES FROM PALM KERNEL SHELL AND COCONUT HUSK , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 2 (2025): FUTA Journal of Engineering and Engineering Technology
- J S. Ajiboye, B. A. Okey-Amechi, Influence of Accumulative back Extrusion and Lubricants on the Hardness of Al 6063 Alloy , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 9 No. 2 (2015): FUTA Journal of Engineering and Engineering Technology
- O.A. ADEMESO, B.I. ADEYEMO, Physical and Mechanical Characteristics of the Conglomeratic Layer in Akure, Southwestern Nigeria. , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 2 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- I. O. Oladele, O. G. Agbabiaka, O. S. Akinola, H. K. Talabi, Development of Sponge Fiber and Particulate Palm Kernel Shell Ash Reinforced Polypropylene Hybrid Composites , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 10 No. 2 (2016): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.
