Propagation Path Loss Model for FM Radio Stations In South West, Nigeria
- Authors
-
-
Y. O. Olasoji
Department of Electrical and Electronics Engineering, Federal University of Technology, Akure, Nigeria
-
S. A. Oyetunji
Department of Electrical and Electronics Engineering, Federal University of Technology, Akure, Nigeria
-
- Keywords:
- Array, Array, Array, Array, Array
- Abstract
-
Quality coverage is the key goal in broadcasting industry. Propagation prediction is useful in determining the effect of the channel on the signal between the transmitter and the receiver. It is based on the scientific modeling of the radio path for predicting accurately signal strength at various frequencies over distances influenced by ground conductivity, atmospherics and terrain. This work sets out to determine the propagation model that is best suitable for predicting the path loss of VHF radio signals in Southwestern part of Nigeria using Federal University of Technology, Akure (FUTA) frequency modulated (FM) radio station as a case stiudy. Empirical approach was adopted to arrive at the model and the result was compared with some existing prediction models which have wide acceptability. The result shows high level of correlation which makes it useful in antenna orientation and for predicting FM signals propagation in South Western part of Nigeria.
- References
- Downloads
- Published
- 2020-04-09
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- Babatunde Oluwamayokun Soyoye, Tehinse, T. O., Design and Fabrication of a Maize Shelling Machine , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 2 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- O. A. Agbolade, EVALUATING LORAWAN ADAPTIVE DATA RATE EFFECTIVENESS IN HETEROGENOUS SMART FARMING CONDITIONS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 20 No. Special (2026): FUTA JEET: Special Issue on Innovative Solutions for Sustainable Living and Environmental Challenges: Engineering Perspectives
- Adebayo Felix Owa, Abdulahi Olawale Adebayo, Olawale Olarewaju Ajibola, Oluwole Daniel Adigun, Sunday Gbenga Aborisade, Fisayo Adesina, Corrosion Behaviour of Low Carbon Steel in Sulphide Medium Using Thevetia Peruviana as Inhibitor , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 2 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- D. T. Oloruntoba, S. O. Seidu, Effect of Mill Scale Particulate in Sand Mould on the Microstructure and Mechanical Properties of Cast 6063 Aluminium Alloys , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 8 No. 2 (2014): FUTA Journal of Engineering and Engineering Technology
- J. M. Jabar, L. Lajide, A. O. Adetuyi, B. J. Owolabi, G. W. Ayoade, Chemical Modification of Coir, Empty Fruit Bunch and Palm Kernel Fibres for Polymer Reinforcement , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 1 (2017): FUTA Journal of Engineering and Engineering Technology
- O. Z. Ayodeji, A. A. Adegun, S. A. Anjorin, DEVELOPMENT AND PERFORMANCE EVALUATION OF A SMALL-SCALE GROUNDNUT SHELLING MACHINE , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 2 (2021): FUTA Journal of Engineering and Engineering Technology
- P. M. Enyong, Performance of a Short Transmission Line Module under Various Loads: A Comparative Evaluation , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 2 (2018): FUTA Journal of Engineering and Engineering Technology
- Y. O. Olasoji, Characterization of Noise in Narrowband Power Line Communications , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 1 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- P. A. Adesida, W. A. Salawudeen, ASSESSMENT OF THE INFLUENCE OF MECHANICAL PROPERTIES AND MINERALOGICAL COMPOSITION ON FRAGMENTATION OF SELECTED GRANITIC ROCKS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 20 No. 1 (2026): FUTA Journal of Engineering and Engineering Technology
- Ajaka, E. O, Omotehinse, A. O, Kaunda L, MODELS FOR OPERATIONAL CONTINUITY OF A PRECIOUS METAL MINE UNDER FLUCTUATING COMMODITY MARKET , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 17 No. 2 (2023): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.