PROGRESSIVE FAILURE ANALYSIS OF MULTI-STOREY REINFORCED CONCRETE BUILDINGS UNDER DIFFERENTIAL SETTLEMENT
- Authors
-
-
S. A. Alabi
Department of Civil Engineering, the Federal University of Technology, Akure, Nigeria
-
I. A. Arighaye
Ondo State Ministry of Works, Department of Planning, Design, Research and Statistics, Akure, Nigeria
-
J. O. Afolayan
Department of Civil Engineering, the Federal University of Technology, Akure, Nigeria
-
- Keywords:
- Array, Array, Array, Array, Array
- Abstract
-
Multi-Storey buildings are buildings with many floors above the ground floor, which serve as shelters for man, his properties and activities. Most building/ails because they were only designed for normal loads whereas abnormal loads were not considered. Therefore, this paper investigates the potential for progressive failure of multi-storey reiriforced concrete (RC) buildings under chosen varying degrees of settlement ranging between 2 5 mm and 15 0 mm. The computer-based modelling procedure following Alternative Load Path Method is adopted for progressive failure analysis. A 5-typical frame models based on the beams' cross-sectional dimensions were analyzed. Each of the frames is analyzed under the normal loads, combining with the assumed differential settlement. From the results obtained, it is discovered that the potential for progressive failure of a multi-storey RC building increases with the increase in the degree of differential settlement. At 25 mm to 75 mm settlement, vulnerability to progressive failure is very low as the Demand-Capacity-Ratio (DCR) values of the component members are very small, but from I 00 mm settlement and above the structure exhibits high potential for progressive failure. It is also noted that the potential for progressive failure of the structure decreases upwards the building storeys. The potential for progressive failure is higher in the lower floors than in the upper floors. Also, the rigidity of the structure helps in combating progressive failure under differential settlement.
- References
- Downloads
- Published
- 2020-04-09
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- E. O. Aiyewalehinmi, O. S. Aderinola, Strength Properties of Commercially Produced Sandcrete block in Ikeja: Lagos State , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 9 No. 1 (2015): FUTA Journal of Engineering and Engineering Technology
- A. Fadeyibi, Z. D. Osunde, M. G. Visa, A. A. Okunola, Investigation into properties of starch-based nanocomposite materials for fruits and vegetables packaging - A review , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 1 (2017): FUTA Journal of Engineering and Engineering Technology
- Akinola, A. O, Yaya-Bankole H. J , EMPIRICAL DETERMINATION OF AIR CONDITIOING INSTALLATION AND MAINTENANCE CHALLENGES IN LAGOS STATE, NIGERIA , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 1 (2025): FUTA Journal of Engineering and Engineering Technology
- Oluyemi-Ayibiowu B. D, Bello, O, Falola, K. E, A Feasibility Study of Using Electronic Waste as Bitumen Modifier for Sustainable Road Construction and Maintenance , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 2 (2025): FUTA Journal of Engineering and Engineering Technology
- C. N. Udekwe, A. A. Ponnle, A. O. Omolade, EXPERIMENTAL STUDY ON THE SYNERGISTIC EFFECTS OF COOLING METHODS AND HEAT SINK DESIGN ON THERMOELECTRIC GENERATOR PERFORMANCE , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 20 No. Special (2026): FUTA JEET: Special Issue on Innovative Solutions for Sustainable Living and Environmental Challenges: Engineering Perspectives
- E. O. Ajaka, O. E. Abiodun, Determining The Metal Contents of Leach Liqour from Ihietutu Lead and Zinc Ore, Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 1 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- Owojori, A.O., ROBOTIC MANIPULATOR MODEL AND CONTROL ESTIMATION , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 2 (2025): FUTA Journal of Engineering and Engineering Technology
- Adekoya A. A, Adelabu, O. S. , Kolawole, F. O., DESIGN OF A DUAL DELTA FUSED DEPOSITION MODELLING 3D PRINTER FOR STUDIO CERAMICS PRODUCTION IN NIGERIA , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 1 (2025): FUTA Journal of Engineering and Engineering Technology
- Ajaka E. Oyedele, Alabi O. Oladunni , Omotehinse O. Adeyinka , Minimizing Losses, Socio-environmental Problems and Operational Difficulties in the Activities of Artisanal and Small-scale Gold Mining in Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 18 No. 1 (2024): FUTA Journal of Engineering and Engineering Technology
- O. A. Olubunmi, O. F. Awe, T. R. Ayeni, O. J. Ogundipe, DEVELOPMENT OF A MICROCONTROLLER-DRIVEN OBSTACLE DETECTION AND NAVIGATION SMART EYEGLASSES FOR THE VISUALLY IMPAIRED , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 20 No. Special (2026): FUTA JEET: Special Issue on Innovative Solutions for Sustainable Living and Environmental Challenges: Engineering Perspectives
You may also start an advanced similarity search for this article.