IMPACT HAMMER TEST FOR BAYESIAN PARAMETER IDENTIFICATION OF RAILWAY TRACK SYSTEM
- Authors
-
-
S.A. ALABI
Federal University of Technology, Akure, Nigeria
-
- Keywords:
- Array, Array, Array, Array, Array
- Abstract
-
The current design approach of railway sleeper is majorly based on some simplifications considered in the European guidelines. One example of these simplifications is how the distribution of the ballast under the sleeper is accounted for. When ballast is damaged, the stiffness it provided to support the sleeper is reduced and the dynamic behavior of the sleeper changes. However, these guidelines consider a uniform distribution of ballast stiffness, either along the complete length of the sleeper or limited to the rail seat. The embedding ballast conditions of railway tracks seemingly vary randomly from site to site and the ballast-sleeper interaction is neither uniformly distributed nor fixed. Therefore, there is need to evaluate the health status of the ballast under the existing railway track. A field test was carried out on an existing ballasted track, to obtain the time domain responses under impact excitation. The measured vertical vibrations at different locations on the in-situ sleeper were employed in time-domain Markov chain Monte Carlo (MCMC)-based Bayesian model updating for identification of the railway track system. MCMC was used to ensure that proposed method can be applied even when the problem is unidentifiable. The proposed method identified the distribution of railway ballast stiffness under low-amplitude vibration and the “equivalent†rail stiffness and mass. The model updating results confirmed that the ballast stiffness under the existing sleeper was uniform, which implies that there was no ballast damage under the tested sleeper.
- References
- Downloads
- Published
- 2020-11-24
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- Uwadia, O.A., Dahunsi, F.M., SOIL NUTRIENT PREDICTION AND CROP PREDICTION RECOMMENDATION SYSTEMS USING IOT AND AI TECHNIQUES: CURRENT TRENDS AND CHALLENGES , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 20 No. Special (2026): FUTA JEET: Special Issue on Innovative Solutions for Sustainable Living and Environmental Challenges: Engineering Perspectives
- O. Adukwu, E. D. Oku, O. I. Apeh, Bivariate Empirical Modeling of Global System for Mobile-Communication (GSM) Propagation Path Loss in an Undulating Terrain , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 2 (2018): FUTA Journal of Engineering and Engineering Technology
- Oyefeso, B, Yusuff, O. A., Fadele, O. K, DEVELOPMENT OF PREDICTIVE MASS AND VOLUME MODELS FOR AFRICAN BUSH MANGO (Irvingia gabonensis) , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 1 (2025): FUTA Journal of Engineering and Engineering Technology
- M. A. Tijani, W. O. Ajagbe, O. A. Agbede, Modelling the Effect of Burning Temperature and Time on Chemical Composition of Sorghum Husk Ash for Optimum Pozzolanic Activity , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 2 (2018): FUTA Journal of Engineering and Engineering Technology
- J.A. GBADEYAN, O.T. OLOTU, NATURAL VIBRATION ANALYSIS OF A TAPERED ROTATING PRESTRESSED RAYLEIGH BEAM USING DIFFERENTIAL TRANSFORM METHOD , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 2 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- S. O. Obayopo, F. J. Banjoko, S. A. Balogun, H. B. Adedayo, Investigation into the Use of Blended Sunflower Oil and Superolein in Hydraulic Systems , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 1 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- Ojo Oluwole Timothy , 2Adeniji Toyosi Adelowokan, DEVELOPMENT OF A BIOMETRIC, FACIAL RECOGNITION AND AUTHENTICATION SYSTEM FOR CLASS ATTENDANCE MANAGEMENT , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 1 (2025): FUTA Journal of Engineering and Engineering Technology
- Bayode O, Folowosele, T, Akinpelu, O. M, Braimah, J. I , Morakinyo T, WORKABILITY AND MECHANICAL PERFORMANCE ASSESSMENT OF TIGERNUT FIBRE CONCRETE FOR SUSTAINABLE CONSTRUCTION , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 1 (2025): FUTA Journal of Engineering and Engineering Technology
- Oluwole Timothy Ojo, FINITE ELEMENT ANALYSIS OF REDESIGNED PIPE-WRENCH FOR OILFIELD SERVICING , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 1 (2025): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.