Assessment of Mechanical Properties of Hybrid Composites Based on Polypropylene and Vegetable Fibers
- Authors
-
-
I. O. Oladele
Department of Metallurgical and Materials Engineering, Federal University of Technology Akure
-
O. G. Agbabiaka
Department of Metallurgical and Materials Engineering, Federal University of Technology Akure
-
A. S. Ogunbadejo
Department of Metallurgical and Materials Engineering, Federal University of Technology Akure
-
M. A. Okoro
Department of Metallurgical and Materials Engineering, Federal University of Technology Akure
-
- Keywords:
- Array, Array, Array, Array, Array
- Abstract
-
This research aim at developing hybrid composites from natural fibers with improved mechanical properties targeted in applications where high strength to weight ratio is required. In this work, Homopolymer Polypropylene (PP) was used as matrix material while coconut (cocos nucifera) and sponge (luffa cylindrica) fibers were used as reinforcing material to produce hybrid composites and to evaluate their mechanical properties such as tensile and flexural properties. Selected fibers were locally sourced and extracted. Composites was developed by initially treating the fibers in one molar concentration of sodium hydroxide (NaOH) before mixing in predetermined proportion with polypropylene matrix using coconut/sponge fibers of 2/8, 4/6, 6/4 and 8/2 wt %. The development of hybrid composites was carried out by heating compression moulding technique. From the result of the mechanical properties that were performed on the samples, hybrid composite samples show the highest flexural and tensile strength when compared to monolithic composite samples. Furthermore, all the composites gave better results when compared to the unreinforced PP sample.
- References
- Downloads
- Published
- 2019-04-25
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- Dung, M. D.,, Anowai, S.I, Peter, J.A, Dapiya, S.H, Okechalu, J.N, Mawak, J.D, ASSESSMENT OF THE COMPRESSIVE AND SPLITTING TENSILE STRENGTHS OF BIOCONCRETE FROM UREOLYTIC BACTERIA. , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 17 No. 2 (2023): FUTA Journal of Engineering and Engineering Technology
- J T Fasinmirin, D O Rapheal, J Lazarus, SOIL CHARCTERIZATION AND MAIZE (Zea mays L.) EVAPOTRANSPIRATION (ETc) IN OMU-ARAN HUMID GEOLOGICAL ZONE OF NIGERIA , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 1 (2018): FUTA Journal of Engineering and Engineering Technology
- S. A. Alabi, I. A. Arighaye, J. O. Afolayan, PROGRESSIVE FAILURE ANALYSIS OF MULTI-STOREY REINFORCED CONCRETE BUILDINGS UNDER DIFFERENTIAL SETTLEMENT , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 1 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- Oyeleye, M. O, Melodi, A. O. , MODELING OF EFFICACIOUS LIGHTNING PROTECTION SCHEME ON NIGERIAN 11-132 kV SUBSTATIONS USING CONE OF PROTECTION METHODS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 17 No. 1 (2023): FUTA Journal of Engineering and Engineering Technology
- M. M. Melodi, O. S. Adekinya, Assessment of Cost Effectiveness of Borehole Drilling in Oyo State, Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 10 No. 1 (2016): FUTA Journal of Engineering and Engineering Technology
- Uwadia, O.A., Dahunsi, F.M., SOIL NUTRIENT PREDICTION AND CROP PREDICTION RECOMMENDATION SYSTEMS USING IOT AND AI TECHNIQUES: CURRENT TRENDS AND CHALLENGES , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 20 No. Special (2026): FUTA JEET: Special Issue on Innovative Solutions for Sustainable Living and Environmental Challenges: Engineering Perspectives
- C. O. Ijagbemi, Design and Optimization of A Gas Turbine Waste Heat Recovery System , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 2 (2019): FUTA Journal of Engineering and Engineering Technology
- A. S. Abubakar, Y. A. Sha'aban, Multiple Model Predictive Control for DFIG Based Wind Energy Conversion System , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 1 (2019): FUTA Journal of Engineering and Engineering Technology
- K.O. OLADOSU, E.O. OLAFIMIHAN, O.R. OYETUNJI, M.O. ADEOTI, A.A. ADEJARE, Influence of Kaolin Additive on Ash Yield of Palm Kernel-Cashew Shell Combustion: Effect of Kaolin Additive on Ash Yield of Palm Kernel- Cashew Shell Combustion , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 2 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- Alfred, V. A, Saliu, M. A, Omoegun, S.O. , Odeyemi, O. Y. , ASSESSMENT OF OXIDE PROPERTIES OF CLAY DEPOSITS FROM ANAMBRA GEOLOGICAL BASIN FOR THEIR SUITABILITY AS CERAMIC RAW MATERIALS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 17 No. 1 (2023): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.