Strength Properties of Stabilised Laterite as Replacement of Sand in Sandcrete Block Production
- Authors
-
-
S. O. Osuji
Department of Civil Engineering, University of Benin, Benin City, Nigeria
-
P. N. Ogbeifun
Department of Civil Engineering, University of Benin, Benin City, Nigeria
-
- Keywords:
- Array, Array, Array, Array, Array, Array
- Abstract
-
This research borders on the effect of strength on the replacement of sand with stabilized laterite in the production of sandcrete blocks in Benin City. It involves the stabilization of the laterite with 15% cement before being used in the production of sandcrete block. Lateritic soils were obtained from 1m depth in Dentistry Quarters of the University of Benin while sharp sand were drilled from Okhuahia River, in Benin City. The samples were taken to the laboratory where controlled testing and curing. The stabilised laterite was used to gradually replace sand at the rate of 10%, 20%, 30%, 40%, 50% and then completely at 100% in the production of sandcrete blocks. A total 54 sandcrete blocks were prepared in 0.001 m3 mould and cured for 7, 14 and 21 days, after which the compressive strength of the blocks were determined and compared with the Nigerian Industrial standards (NIS) as well as the British standard (BS 2028) for minimum strength considerations. The results of tests carried out indicate that there was an improvement in the strength of the sandcrete block when there was a complete replacement of the stabilized laterite with sand in the production of sandcrete blocks. The least strength results obtained showed that for each percentage replacement of sand with stabilised laterite, the minimum compressive strength exceeded that specified by NIS for block production. This is quite important in reducing the cost of sand in block production.
- References
- Downloads
- Published
- 2019-04-25
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- Ogundele, O. J, Adebisi, O. I, Adejumobi, I. A, Amusa, K. A. , Alabi, A. A, POWER QUALITY ENHANCEMENT IN AN ELECTRICAL DISTRIBUTION NETWORK USING SHUNT PASSIVE FILTER , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 18 No. 1 (2024): FUTA Journal of Engineering and Engineering Technology
- Adeyanju, Olusiji Ayoade , Adeosun, Tunde Adamson, PRODUCTION ANALYSIS OF FIVE-SPOT MISCIBLE DISPLACEMENT SCHEMES IN GAS CONDENSATE RESERVOIRS. , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 1 (2025): FUTA Journal of Engineering and Engineering Technology
- Talabi H. K. , GREEN SYNTHESIS AND CHARACTERIZATION OF COPPER NANOPARTICLES AS REINFORCEMENT IN EPOXY BASED COMPOSITE USING SPONDIAS MOMBIN LEAF EXTRACT , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 18 No. 2 (2024): FUTA Journal of Engineering and Engineering Technology
- A. O. Melodi, B. O. Akinloye, Transmission Capacity Enhancement for Nigerian Power Transmission Grid using TCSC and UPFC , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 8 No. 2 (2014): FUTA Journal of Engineering and Engineering Technology
- M. O. Oyeleye, T. O. Ale, Foundational Steel Reinforcement Earthing Evaluation: Case of Ogomudia Electrical/Electronics Laboratory Building Extension, Federal University Of Technology, Akure , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 1 (2019): FUTA Journal of Engineering and Engineering Technology
- O. O. Awopetu, Effect of Rake Face Reinforcement on Cutting Tool Life of Cemented Carbide Tools during Turning of a-Titanium Alloy , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 1 (2017): FUTA Journal of Engineering and Engineering Technology
- Kareem, B, Alabi, S. A., WORKPLACE REORGANISATION FOR PRODUCTIVITY ENHANCEMENT IN FAST MOVING GOODS INDUSTRY , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 17 No. 1 (2023): FUTA Journal of Engineering and Engineering Technology
- O. ADERINLEWO, B. ARIBISALA, A. AFOLAYAN, M. TANIMOLA, COMPARATIVE ANALYSIS OF THE USE OF BAMBOO STEM ASH AND CEMENT FOR LATERITIC SOIL STABILIZATION , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 2 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
You may also start an advanced similarity search for this article.