EFFECTS OF WOODASH AND SAWDUST ADMIXTURE ON ENGINEERING PROPERTIES OF BURNT LATERITE CLAY BRICKS
- Authors
-
-
R. F. Falayi
Department of Agricultural and Environmental Engineering, Federal University of Technology, Akure, Ondo State, Nigeria.
-
P. A. Adeduntan
Department of Agricultural and Environmental Engineering, Federal University of Technology, Akure, Ondo State, Nigeria.
-
- Keywords:
- Array, Array, Array, Array, Array, Array, Array, Array
- Abstract
-
Over the years, excessive energy consumption is one of the major problems associated with burnt brick production. This study assessed the characteristics of burnt bricks containing sawdust and wood ash as additive. Trial test was prepared from standard mix. It was done in different percentage of additives (0%, 10%, 20%, 30%, 40% and 50%) blend of sawdust and wood ash. One hundred and thirty- two (132) brick samples were cast out of which 99 were used for compressive strength. Specimen samples were fired at temperature 1100oC. The result obtained showed that the highest compressive strength obtained in the control samples with 6.05 N/mm2, sawdust with 3.05 N/mm2 and wood ash 1.58 N/mm2 when fired at 1100oC. It was observed that there was a decrease in compressive strength as the percentage of sawdust increases and wood ash increases. The research concluded that regarding the compressive strength, the samples met the requirement specified by (IS: 1077) at temperatures of 800oC, 900oC, 1000oC and 1100oC considered to have good resistance to abrasion. Bricks with those parameters are suitable for use in the construction of building as a walling material. It was also concluded that samples with additives are more stabilized before firing than the control, though higher strength was obtained in the control than samples with additives and both met the standard specification. It is recommended that the firing temperature of bricks made with sawdust and wood ash should not exceed 1100oC to avoid distortion.
- References
-
Aeslina A.K and Abbas M (2018). Bricks: An excellent building material for recycling wastes. Proceedings of the IASTED International Conference Environmental Management and Engineering, July 4 – 6 2011 Calgary, AB, Canada. DOI: 10.2316/p.2011. 736 – 029.
Asokan P, Mohini S and Shyam R.A(2011). Solid Wastes Generation in India and their Recycling Potential in Building Materials. Canadian Journal on Environmental, Construction and Civil Engineering, Vol 2, No 3, 265-275.
Ayangade, J. A., Olusola K. O., Ikpo, I. J. and Ata O. (2019). Effect of granite dust on the performance characteristics of Kernelrazzo floor finish. Building and environment,39, 1207 – 1212.
Emmanuel I.U, Dickson A, Famuyibo (2014). Analysis of the Effect of Blending Nigeria
Pure.Clay with Rice Husk: A Case Study of
Ekulu Clay in Enugu State. American Journal of Material Engineering and Technology Vol 2, No1, 34-37
Hendry, A.W., Sinha, B. P., and Davies, S. R. 2017). Load bearing brickwork design. (2nded.). England: Ellis Horwood Ltd.
Mawusi SK, Shrestha P, Xue C, Liu G. (2023). A comprehensive review of the production, adoption and sustained use of biomass pellets in Ghana. Heliyon. 2023;9(6):1–22. https://doi. org/ 10. 1016/j. heliy on. 2023. e16416.
National Building code (2006).” Building Regulation”, LexisNexis Butterworths, Ohio. Nigerian Industrial Standards. NIS 087:2000. Specification for Sandcrete Blocks.
Standards Organisation of Nigeria.NBRRI (2023). Housing in Nigeria (A Book Reading). A Manual of Proceeding of Seminar.
Okunade, E.A. (2015). The effect of wood ash and sawdust admixtures on the engineering properties of a burnt laterite –clay brick. J. Applied Sci., 8, pp 1042- 1048.
Okunade, E.A. (2015). The effect of wood ash and sawdust admixtures on the engineering properties of a burnt laterite –clay brick. J. Applied Sci., 8, pp 1042 – 1048.
Olusola K.O, Ogunbode E.B and Kyenge S.S (2023). Performance Assessment of Makurdi Burnt Bricks. https://www.slideshare.net.slide show.
Rajput, R. K (2019). “Engineering Materials (Including Construction Materials). A Textbook for Engineering Students of B.E., Section -B of A S. Chand & Company Limited, New Delhi, India.
Saibal G (2021). The Eastern Ghats Belts INDLA – A New Look at an Old Orogen. Journal of Geological Survey India spl, No 48 pp: 75-100.
Sampson A., Charles K.K., Kwadwo A.A., Russell O.A. and Jones O.T. (2024). Effects of Burnt Sawdust Ashes from Timber Species on the Strength Properties of Laterite- Interlocking Blocks. Journal of Discover Civil Engineering, (2024) 1:87 |https://doi.org/10.1007/s44290-024-00093-9.
- Downloads
- Published
- 2026-04-18
- Section
- Articles
- License
-
Copyright (c) 2026 FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY

This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- T E Abioye, DEVELOPMENT OF A POULTRY DE-FEATHERING MACHINE WITH AN ADJUSTABLE BASIN , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 1 (2018): FUTA Journal of Engineering and Engineering Technology
- Dafiewhare, O, Ijagbemi, C. O, Ologunwa, T. P, Alabi, O. T, Ijagbemi, A. O, PRODUCTION AND EVALUATION OF BIOMASS BRIQUETTES FROM PALM KERNEL SHELL AND COCONUT HUSK , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 2 (2025): FUTA Journal of Engineering and Engineering Technology
- J S. Ajiboye, B. A. Okey-Amechi, Influence of Accumulative back Extrusion and Lubricants on the Hardness of Al 6063 Alloy , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 9 No. 2 (2015): FUTA Journal of Engineering and Engineering Technology
- P B Mogaji, DEVELOPMENT OF AN IMPROVED CIRCULAR SAWING MACHINE , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 2 (2018): FUTA Journal of Engineering and Engineering Technology
- O. O. Omotayo, S. L. Akingbomire, C. M. Ikumapayi, Sustainable Application of Materials from Construction and Demolition Waste: A Review , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 2 (2019): FUTA Journal of Engineering and Engineering Technology
- Okewale, I.A, Fasan, J.O, Abiwo, O.O, DEVELOPMENT OF A FLOATING RING OEDOMETER FOR TESTING GEOMATERIALS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 18 No. 1 (2024): FUTA Journal of Engineering and Engineering Technology
- M. A. Tijani, W. O. Ajagbe, O. A. Agbede, Modelling the Effect of Burning Temperature and Time on Chemical Composition of Sorghum Husk Ash for Optimum Pozzolanic Activity , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 2 (2018): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.
