BRIDGING RESEARCH-INDUSTRY DIVIDE IN FOOD AND BEVERAGE ENTERPRISES: EMPIRICAL EVIDENCE FROM SOUTHWESTERN NIGERIA
- Authors
-
-
A. D. Dada
Federal University of Technology, Akure
-
- Keywords:
- Array
- Abstract
-
This paper investigates the gaps between research institutions and industry in R&D collaboration towards the promotion of innovation, creativity and competitiveness among food and beverage enterprises (FBEs) in Nigeria. This was measured by the level impact of R&D institutional support services for technological innovations in the industry. A multi-staged sampling method was adopted to select 150 registered FBEs from three small and medium scale enterprises (SMEs) populated States in Southwestern Nigeria with a response rate of 64% recorded. Adopting model regression analysis, the study showed that the contributions of R&D institutions to innovative performance of the industry was low (R2 = 0.008). However, training and information dissemination (β=36.49, P≤ 0.05) and provision of analytical services (β = 36.67, P≤ 0.05) were found to have significant impact on the innovative performance of the industry. No significant difference (F=0.336, P≤ 0.05) between the two methods of support services was confirmed in the study. The study concludes that the R&D support services from research institutions to FBEs were inadequate. Policy intervention is needed to encourage R&D institutions to adequately support the food and beverage industry in Nigeria.
- References
- Downloads
- Published
- 2019-04-29
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- M. O. Oyeleye, T. O. Ale, Foundational Steel Reinforcement Earthing Evaluation: Case of Ogomudia Electrical/Electronics Laboratory Building Extension, Federal University Of Technology, Akure , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 1 (2019): FUTA Journal of Engineering and Engineering Technology
- Adeyemo, Z.K, Bamikefa, I.A, Akande D.O, Ojo, S.I., , Ojerinde, I. A, OPTIMIZATION OF COST 231-HATA PROPAGATION MODEL FOR SELECTED FREQUENCY MODULATION STATIONS IN OSUN STATE, NIGERIA , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 17 No. 1 (2023): FUTA Journal of Engineering and Engineering Technology
- J. J. Popoola, D. O. Akinfenwa, I. O. Animasahun, Assessment of Electromagnetic Radiation Effects and Safety Issues of GSM-900 and GSM-1800 Radio Frequencies – A Case Study of Akure, Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 9 No. 1 (2015): FUTA Journal of Engineering and Engineering Technology
- O. A. Adetola, O. J. Olukunle, T. L. Aremu, Investigation of The Effects of Yield On Selected Physical Properties of Cassava Tubers , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 10 No. 2 (2016): FUTA Journal of Engineering and Engineering Technology
- P. B. Mogaji, T. E. Abioye, N. O. Ohuruogu, Development of Epoxy Resin Composite Reinforced With Cow Horn and Cassava Particles for Car Dashboard , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 1 (2017): FUTA Journal of Engineering and Engineering Technology
- Ikem, I.A., Akintunde, M. A, Titiladunayo, I. F, Awatt.E, INVESTIGATING THE THERMODYNAMIC CHARACTERISTICS OF ENERGY SAVING REFRIGERATING SYSTEM WITH COLD ACCUMULATOR , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 2 (2025): FUTA Journal of Engineering and Engineering Technology
- E. C. Umeh, A. F. Isiaka, Analysis of the Short Fall in Production Target and Specific Cost of Unit Operations in National Iron Ore Mining Company NIOMCO, Itakpe. , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 8 No. 2 (2014): FUTA Journal of Engineering and Engineering Technology
- A. Fadeyibi, Z. D. Osunde, M. G. Visa, A. A. Okunola, Investigation into properties of starch-based nanocomposite materials for fruits and vegetables packaging - A review , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 1 (2017): FUTA Journal of Engineering and Engineering Technology
- Ayanshola, A.M., , Adidu, J.A, Iji, J.O., , Oladimeji, S.B, Sule, B.F, Salami, A.W. , Bilewu, S.O., ESTIMATING THE POTENTIAL FOR RAINWATER HARVESTING IN ILORIN, NORTH CENTRAL, NIGERIA , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 18 No. 1 (2024): FUTA Journal of Engineering and Engineering Technology
- B. V. Omidiji, H. A. Owolabi, T. A. Morakinyo, A. Olukoga, Effects of Machining Parameters on the Surface Roughness of Al-Si alloy , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 9 No. 2 (2015): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.