SOIL CHARCTERIZATION AND MAIZE (Zea mays L.) EVAPOTRANSPIRATION (ETc) IN OMU-ARAN HUMID GEOLOGICAL ZONE OF NIGERIA
- Authors
-
-
J T Fasinmirin
-
D O Rapheal
-
J Lazarus
-
- Keywords:
- Array
- Abstract
-
Development of crop coefficient (Kc) can enhance crop water requirement estimates at specific crop growth stages. However, local Kc data are lacking for maize in Omu-aran. Therefore, this research was aimed at quantifying water use and specific Kc values at different growth stages for maize (Zea mays L.) in Omu-Aran,a sub-humid agro-geological zone of Nigeria. A 60cm diameter and 45cm high drainage lysimeter was designed, constructed from a 2.5 mm thick plastic drum, and installed. CROPWAT 8.0 model was later used to develop the Kc and ETc (crop evapotranspiration) using the local weather data of the study site. Soil physical and chemical properties, moisture content, bulk density, and porosity of the site were determined. Weather parameters such average monthly temperature, wind speed, rainfall and relative humidity etc. were collected from an automatic meteorological station located around the research site. Also, irrigation requirements and scheduling for the crop were determined from the model. The average ETc values were 14.6, 43.75, 60.38, and 38.67.0 mm during the initial, development, mid-season and late-season stages, respectively, and the total ETc was 561.8 mm, while the average Kc values for maize were 0.30, 0.73, 1.29 and 0.91 for the initial, development, mid-season, and late-season stages, respectively. The values obtained are suitable for a successful design and implementation of irrigation programme for maize in the study area and this will eventually mean higher productivity and economic development.
- References
- Downloads
- Published
- 2019-04-29
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- E. I. Bello, I. A. Daniyan, T. I Ogedengbe, L. Lajide, P. B. Mogaji, Development of a Model for Predicting the Yield of Biodiesel During Biodiesel Production , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 1 (2017): FUTA Journal of Engineering and Engineering Technology
- O. O. Alabi, T. A. Olatunji, Y. Gbadamosi, Geochemical and Mineralogical Characterization of Ore – Mineral Assemblages from Black Sands in Akure South Area, South - Western Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 1 (2019): FUTA Journal of Engineering and Engineering Technology
- S.A. ALABI, IMPACT HAMMER TEST FOR BAYESIAN PARAMETER IDENTIFICATION OF RAILWAY TRACK SYSTEM , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 2 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- Ijagbemi, C.O. , Olabanji, O. M, Abdulmumuni, B, Ashiru, A.R, IJagbemi F.M, PRODUCTION OF ETHANOL GEL FROM CASSAVA AND BANANA PEELS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 1 (2025): FUTA Journal of Engineering and Engineering Technology
- Oluwaseun Opeyemi Martinsa, Muhammad Abdulhamid Mahdia, David Tiwaloluwa Adegokea, Olusola Esther Omoniyia, Pius Benmoore Gabriela, DESIGN AND IMPLEMENTATION OF AN ELECTRONIC ATTENDANCE AND ADMITTANCE SYSTEM WITH FINGERPRINT AUTHENTICATION USING PATTERN MATCHING , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 18 No. 2 (2024): FUTA Journal of Engineering and Engineering Technology
- S. S. Yaru, I. K. Adegun, M. A. Akintunde, Comparative Study on Ignition Time of Biogas from Cattle Dung and Mixtures of Cattle Dung with Cassava Peels , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 9 No. 1 (2015): FUTA Journal of Engineering and Engineering Technology
- E I BELLO, F I OTU, T I OGEDENGBE, L LAJIDE, PERFORMANCE EVALUATION OF RUBBER SEED OIL BIODIESEL , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 2 (2018): FUTA Journal of Engineering and Engineering Technology
- A. Fadeyibi, Z. D. Osunde, M. G. Visa, A. A. Okunola, Investigation into properties of starch-based nanocomposite materials for fruits and vegetables packaging - A review , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 1 (2017): FUTA Journal of Engineering and Engineering Technology
- O. A. Dahunsi, M. O. Adeoti, O. O. Awopetu, F. O. Aramide, O. O. Alabi, A. S. Abdulkareem, Characterization of Saman-Burkono (Nigeria) Graphite for Crucible Production , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 1 (2019): FUTA Journal of Engineering and Engineering Technology
- M. A. Tijani, W. O. Ajagbe, O. A. Agbede, Modelling the Effect of Burning Temperature and Time on Chemical Composition of Sorghum Husk Ash for Optimum Pozzolanic Activity , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 2 (2018): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.