SOIL CHARCTERIZATION AND MAIZE (Zea mays L.) EVAPOTRANSPIRATION (ETc) IN OMU-ARAN HUMID GEOLOGICAL ZONE OF NIGERIA
- Authors
-
-
J. T. Fasinmirin
Federal University of Technology, Akure
-
D. O. Rapheal
Federal University of Technology, Akure
-
J. Lazarus
Federal University of Technology, Akure
-
- Keywords:
- Array
- Abstract
-
Development of crop coefficient (Kc) can enhance crop water requirement estimates at specific crop growth stages. However, local Kc data are lacking for maize in Omu-aran. Therefore, this research was aimed at quantifying water use and specific Kc values at different growth stages for maize (Zea mays L.) in Omu-Aran,a sub-humid agro-geological zone of Nigeria. A 60cm diameter and 45cm high drainage lysimeter was designed, constructed from a 2.5 mm thick plastic drum, and installed. CROPWAT 8.0 model was later used to develop the Kc and ETc (crop evapotranspiration) using the local weather data of the study site. Soil physical and chemical properties, moisture content, bulk density, and porosity of the site were determined. Weather parameters such average monthly temperature, wind speed, rainfall and relative humidity etc. were collected from an automatic meteorological station located around the research site. Also, irrigation requirements and scheduling for the crop were determined from the model. The average ETc values were 14.6, 43.75, 60.38, and 38.67.0 mm during the initial, development, mid-season and late-season stages, respectively, and the total ETc was 561.8 mm, while the average Kc values for maize were 0.30, 0.73, 1.29 and 0.91 for the initial, development, mid-season, and late-season stages, respectively. The values obtained are suitable for a successful design and implementation of irrigation programme for maize in the study area and this will eventually mean higher productivity and economic development.
- References
- Downloads
- Published
- 2019-04-29
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- K.F. AKINGBADE, SURVEY OF EXISTING FACE RECOGNITION APPROACHES, TECHNIQUES AND CHALLENGES , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 2 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- Akinola, A. O, Yaya-Bankole H. J , EMPIRICAL DETERMINATION OF AIR CONDITIOING INSTALLATION AND MAINTENANCE CHALLENGES IN LAGOS STATE, NIGERIA , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 1 (2025): FUTA Journal of Engineering and Engineering Technology
- Giwa A.M., Olatunji O. K. , Mohammed Dikko Almustapha, Muhammad.Z.Z, Agbon E.E, Yau.I, Sena Timothy Tersoo, SIGNAL MONITORING AND ANALYSIS FOR ENHANCED TRUSTWORTHINESS IN 5G TELECOMMUNICATIONS NETWORKS: AN OVERVIEW OF THE CHALLENGES FACED AND SOLUTIONS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 18 No. 2 (2024): FUTA Journal of Engineering and Engineering Technology
- Ogbozige, F.J., APPLICATION OF GIS TECHNIQUES IN GENERATING RAINFALL-IDF MAPS FOR UNGAUGED CATCHMENT: A CASE OF YENAGOA CITY, NIGERIA , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 17 No. 2 (2023): FUTA Journal of Engineering and Engineering Technology
- SAMUEL AKINGBONMIRE, Fault Tree–Based Reliability Analysis of Reinforced Concrete Elements in an Institutional Building , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 20 No. 2 (2026): FUTA Journal of Engineering and Engineering Technology
- E. O. Aiyewalehinmi, O. S. Aderinola, M. O. Tanimola, An Investigation into Building Functional Failures in Nigeria (A Case Study of Ibadan, Oyo State Capital) , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 9 No. 2 (2015): FUTA Journal of Engineering and Engineering Technology
- M O Idris, EVALUATION OF EFFECTS OF EXTERNAL FACTORS ON DUE DATES PREDICTION IN MANUFACTURING JOBSHOPS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 2 (2018): FUTA Journal of Engineering and Engineering Technology
- J. M. Jabar, L. Lajide, A. O. Adetuyi, B. J. Owolabi, G. W. Ayoade, Chemical Modification of Coir, Empty Fruit Bunch and Palm Kernel Fibres for Polymer Reinforcement , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 1 (2017): FUTA Journal of Engineering and Engineering Technology
- W. A. Raheem, A. O. Ajayeoba, K. A. Adebiyi, O. R. Oyetunji, O. A. Ayeyemi, Ergonomic Evaluation of Base Transceiver Station Maintenance Personnel in Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 1 (2019): FUTA Journal of Engineering and Engineering Technology
- T. S. Mogaji, A. Akinsade, M. A. Akintunde, Pyrolysis of Sugarcane Bagasse for Bio-Oil Production , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 2 (2019): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.