SYNERGISTIC EFFECT OF CO-DIGESTING DIFFERENT MIX RATIOS OF WATER HYACINTH AND COW-DUNG FOR BIOGAS PRODUCTION.
- Authors
-
-
Ochuko Mary Ojo
1Department of Civil and Environmental Engineering, the Federal University of Technology, Akure, PMB 704, Ondo State, Nigeria
-
J O Babatola
ATODATECH LLC, 742 Locust St, #301, Pasadena, CA, USA 91101.
-
A A Adesina
3Department of Mechanical Engineering, the Federal University of Technology, Akure, PMB 704, Ondo State, Nigeria
-
A O Akinola
1. Department of Mechanical Engineering, The Federal University of Technology Akure, Ondo State. Nigeria.
-
Olurinde Lafe
Centre for Renewable Energy, the Federal University of Technology, Akure, PMB 704, Ondo State, Nigeria
-
- Keywords:
- Array
- Abstract
-
The synergistic effect of co-digesting water hyacinth (WH) with cow-dung (CD) for optimum biogas production was evaluated. Different mix ratios of WH to CD were digested in a laboratory scale anaerobic digester over a retention time of 40 days. The volume of biogas produced was determined using water displacement method. The ultimate biogas yield and synergy factors for all the mixes were calculated. The third order polynomial curve for the different mixes had a R2 value of 0.9834 which is quite significant. The curve also showed that the highest ultimate biogas yield of 141.72 L was produced by 2 WH: 8 CD and impressively makes it the best CD-aided WH digestion mix. The highest synergy factor of 1.31 was observed for 2 WH: 8 CD which collaborates the fact that the best mix of CD-aided WH digestion in terms of biogas yield is 2 WH: 8 CD.
- References
- Downloads
- Published
- 2019-04-29
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- I. O. Oladele, O. G. Agbabiaka, O. S. Akinola, H. K. Talabi, Development of Sponge Fiber and Particulate Palm Kernel Shell Ash Reinforced Polypropylene Hybrid Composites , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 10 No. 2 (2016): FUTA Journal of Engineering and Engineering Technology
- Robert Oluwayimika Abolade, Oluwaseun Olayinka Tooki, David Oluwagbemiga Aborisade, REVIEW ARTICLE ON THE MITIGATION OF FOUR WAVE MIXING IN OPTICAL COMMUNICATION SYSTEM , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 1 (2021): FUTA Journal of Engineering and Engineering Technology
- J T Fasinmirin, D O Rapheal, J Lazarus, SOIL CHARCTERIZATION AND MAIZE (Zea mays L.) EVAPOTRANSPIRATION (ETc) IN OMU-ARAN HUMID GEOLOGICAL ZONE OF NIGERIA , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 1 (2018): FUTA Journal of Engineering and Engineering Technology
- M. D. IDI, T. A. ALADESANMI, S. LUKMAN, M. A. ASANI, Y. M. USMAN, I. A. OKE, A NUMERICAL FORMULA AND COST BENEFIT OF GROUNDWATER RECHARGE IN MAIDUGURI, NIGERIA , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 2 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- B. V. Omidiji, H. A. Owolabi, T. A. Morakinyo, A. Olukoga, Effects of Machining Parameters on the Surface Roughness of Al-Si alloy , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 9 No. 2 (2015): FUTA Journal of Engineering and Engineering Technology
- Dafiewhare, O, Ijagbemi, C. O, Ologunwa, T. P, Alabi, O. T, Ijagbemi, A. O, PRODUCTION AND EVALUATION OF BIOMASS BRIQUETTES FROM PALM KERNEL SHELL AND COCONUT HUSK , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 2 (2025): FUTA Journal of Engineering and Engineering Technology
- S. O. Osuji, K. A. Ezekiel, E. O. Kenvin, Effect of Coarse Aggregate Type on the Modulus of Elasticity of Concrete , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 9 No. 1 (2015): FUTA Journal of Engineering and Engineering Technology
- O. O. Awopetu, P. K. Farayibi, K. A. Ismail, Optimization of Major Process Parameters for Surface Roughness of ASTM 25 Grey Cast Iron using Taguchi method , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 2 (2017): FUTA Journal of Engineering and Engineering Technology
- E. I. Bello, I. A. Daniyan, T. I Ogedengbe, L. Lajide, P. B. Mogaji, Development of a Model for Predicting the Yield of Biodiesel During Biodiesel Production , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 1 (2017): FUTA Journal of Engineering and Engineering Technology
- O.I. Adebisi, THE EFFECT OF COMBINED SERIES-SHUNT PASSIVE FILTER ON HARMONIC DISTORTION AND POWER LOSSES IN AN ELECTRICAL DISTRIBUTION NETWORK , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 20 No. Special (2026): FUTA JEET: Special Issue on Innovative Solutions for Sustainable Living and Environmental Challenges: Engineering Perspectives
You may also start an advanced similarity search for this article.