FLEXURAL MOTION UNDER MOVING MASSES OF PRESTRESSED SIMPLY SUPPORTED PLATE RESTING ON BI-PARAMETRIC FOUNDATION
- Authors
-
-
T O Awodola
Department of Mathematics, Federal University of Technology, Akure, Nigeria
-
- Keywords:
- Array
- Abstract
-
In this investigation, the flexural vibration of a prestressed and simply supported rectangular plate carrying moving concentrated masses and resting on bi-parametric (Pasternak) elastic foundation is considered. In order to solve the governing fourth order partial differential equation, a technique based on separation of variables is used to reduce the equation with variable and singular coefficients to a sequence of coupled second order ordinary differential equations. The modified method of Struble and the integral transformations are then employed for the solutions of the reduced equations. The numerical results in plotted curves show that as the value of the axial force in x-direction (Nx) increases, the response amplitudes of the plates decrease, the same effect is produced as the axial force in y-direction (Ny) increases for both cases of moving force and moving mass problems of the prestressed and simply supported rectangular plate resting on Pasternak elastic foundation. The deflection of the plate also decreases in each case as the values of the Shear modulus Go and the rotatory inertia correction factor Ro increase. Also, the transverse deflections of the prestressed rectangular plates under the actions of moving masses are higher than those obtained when only the force effects of the moving loads are considered. Further analysis shows that resonance is attained earlier in moving mass problem than in moving force problem and that the critical speed for the moving mass problem is reached prior to that of the moving force problem, implying that it is risky to rely on a design based on the moving force solution. Furthermore, the response amplitudes of the moving mass problem increase with increasing mass ratio and approach those of the moving force as the mass ratio approaches zero for the prestressed and simply supported rectangular plates resting on uniform Pasternak elastic foundation
- References
- Downloads
- Published
- 2019-04-29
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- C. O. Ijagbemi, Design and Optimization of A Gas Turbine Waste Heat Recovery System , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 2 (2019): FUTA Journal of Engineering and Engineering Technology
- O.I. Adebisi, THE EFFECT OF COMBINED SERIES-SHUNT PASSIVE FILTER ON HARMONIC DISTORTION AND POWER LOSSES IN AN ELECTRICAL DISTRIBUTION NETWORK
- Adeyemo A. J., AMELIORATION OF DIFFERENT SOIL TYPES CONTAMINATED WITH SPENT HYDROCARBON. , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 18 No. 2 (2024): FUTA Journal of Engineering and Engineering Technology
- A. A. Akinlabi, A. P. Faluyi, J. M. Iberedem, F. M. Dahunsi, INTERNLY: A MOBILE PLATFORM FOR CONNECTING NIGERIAN STUDENTS TO INTERNSHIP OPPORTUNITIES
- A. R. Iyanda, O. A. Odejobi, Computational Modelling Technique for Short-Term Electric Load Forecasting , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 9 No. 2 (2015): FUTA Journal of Engineering and Engineering Technology
- N G Olaiya, P K Farayibi, P K Oke, A REVIEW ON ADDITIVE MANUFACTURING: LASER TECHNOLOGY METHODS, DISTINCTIONS AND APPLICATIONS IN MANUFACTURING ENGINEERING , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 2 (2018): FUTA Journal of Engineering and Engineering Technology
- M. A. Akintunde, K A ADETORO, T. J. Abioye, Development of Refrigeration System for Storage and Preservation of Yam Tubers , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 2 (2019): FUTA Journal of Engineering and Engineering Technology
- A. O. Owolabi, P. A. Adesida, COST EVALUATION FOR ASPHALT PRODUCTION IN SELECTED QUARRIES , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 1 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- M. M. Melodi, D. A. Agboola, Labour Productivity Assessment of Dredging Operations in Some Selected Companies in Lagos State, Nigeria
- W. A. Raheem, A. O. Ajayeoba, K. A. Adebiyi, O. R. Oyetunji, O. A. Ayeyemi, Ergonomic Evaluation of Base Transceiver Station Maintenance Personnel in Nigeria
You may also start an advanced similarity search for this article.