A MULTI-OBJECTIVE RESOURCE-CONSTRAINED PROJECT SCHEDULING PROBLEM USING GENETIC ALGORITHM
- Authors
-
-
LADI OGUNWOLU
Department of Systems Engineering, Faculty of Engineering, University of Lagos, Nigeria.
-
Adeyanju Sosimi
Department of Systems Engineering, Faculty of Engineering, University of Lagos, Nigeria
-
Toheeb Salahudeen
Department of Systems Engineering, Faculty of Engineering, University of Lagos, Nigeria
-
- Keywords:
- Array
- Abstract
- Resource-Constrained Project Scheduling Problem (RCPSP) has been modeled as a single or multi-objective, using minimization of project make-span, lateness, total weighted start time, total project cost and maximization of project net present value. In this paper, a multi-objective RCPSP incorporated resource idleness into the list of RCPSP objectives. Here, the RCPSP is modeled as a Mixed Integer Non-Linear Programme to depict the various objective factors namely cost, time and resource idleness. Genetic algorithm (GA) meta-heuristic solution technique is used to promote solution diversity and determine the Pareto optimal for the multi-objective problem. The performance of the proposed RCPSP model was evaluated using a standard test problem that consist of 5 activities, 3 reusable resource types and a network diagram; a comprehensive computational experiment was performed and the results were analyzed with precedence relations considering the objectives as single objectives, bi-objectives and in combined form as multi-objectives simultaneously. The integration of resources idleness into the multi-objective policy gives more realistic result.
- References
- Downloads
- Published
- 2019-04-29
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- Ubochi, B. C, Olawumi, A. E., , Shuiabu, A. O. , Akingbade, K. F, A WEARABLE FACIAL RECOGNITION DEVICE FOR THE VISUALLY IMPAIRED , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 18 No. 1 (2024): FUTA Journal of Engineering and Engineering Technology
- O. A. Olubunmi, O. F. Awe, T. R. Ayeni, O. J. Ogundipe, DEVELOPMENT OF A MICROCONTROLLER-DRIVEN OBSTACLE DETECTION AND NAVIGATION SMART EYEGLASSES FOR THE VISUALLY IMPAIRED , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 20 No. Special (2026): FUTA JEET: Special Issue on Innovative Solutions for Sustainable Living and Environmental Challenges: Engineering Perspectives
- M. O. Oyeleye, T. O. Ale, Foundational Steel Reinforcement Earthing Evaluation: Case of Ogomudia Electrical/Electronics Laboratory Building Extension, Federal University Of Technology, Akure , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 1 (2019): FUTA Journal of Engineering and Engineering Technology
- Adeyanju, Olusiji Ayoade , Adeosun, Tunde Adamson, PRODUCTION ANALYSIS OF FIVE-SPOT MISCIBLE DISPLACEMENT SCHEMES IN GAS CONDENSATE RESERVOIRS. , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 1 (2025): FUTA Journal of Engineering and Engineering Technology
- Adeyemo, A. J. , LAND USE EFFECTS ON SOIL CARBON AND NITROGEN ENZYMES IN A HUMID TROPICAL ECOSYSTEMS OF SOUTH WESTERN NIGERIA , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 17 No. 2 (2023): FUTA Journal of Engineering and Engineering Technology
- F. O. Ajibade, J. R. Adewumi, Performance Evaluation of Aquatic Macrophytes in a Constructed Wetland for Municipal Wastewater Treatment , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 1 (2017): FUTA Journal of Engineering and Engineering Technology
- S.A. ALABI, IMPACT HAMMER TEST FOR BAYESIAN PARAMETER IDENTIFICATION OF RAILWAY TRACK SYSTEM , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 2 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- O. Hezekiah Adeyemi, B Julius Olorunfemi,, Olasunkanmi O Akinyemi, APPRAISAL OF RELATED RISKS WITH LOCALLY MADE BLOCK MAKING MACHINE: A MULTI-SITE CASE STUDY OF NIGERIA BLOCK MAKING INDUSTRY , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 2 (2018): FUTA Journal of Engineering and Engineering Technology
- Olutomilola E. O., Otokola T. O. , Ajayi V. A., DEVELOPMENT OF AN ADJUSTABLE HOPPER FOR HAMMER MILL , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 18 No. 1 (2024): FUTA Journal of Engineering and Engineering Technology
- Ajaka, E. O, Omotehinse, A. O, Kaunda L, MODELS FOR OPERATIONAL CONTINUITY OF A PRECIOUS METAL MINE UNDER FLUCTUATING COMMODITY MARKET , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 17 No. 2 (2023): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.