EVALUATION OF EFFECTS OF SELECTED FACTORS ON ADSORPTION KINETICS OF LEAD ION REMOVAL FROM AQUEOUS SOLUTIONS
- Authors
-
-
A Amoko
Department of Chemistry, Adeyemi Federal University Education, Ondo, Nigeria
-
S JUSTINAH
Department of Chemistry, Adeyemi Federal University Education, Ondo, Nigeria;
-
A Fehintola
Department of Chemistry, Adeyemi Federal University Education, Ondo, Nigeria;
-
O Ezekiel
Department of Civil Engineering, Obafemi Awolowo University, Ile-Ife, Nigeria
-
I Oke
at Civil and Environmental Engineering Department, Elizade University, Ilara- Mokin, Ondo State, Nigeria.
-
A Isaiah
Department of Civil Engineering, Obafemi Awolowo University, Ile-Ife, Nigeria
-
- Keywords:
- Array
- Abstract
-
This paper presents a report on the removal of lead ions (Pb2+) from aqueous solutions through adsorption techniques using powdered corncobs. Corncobs were collected from Obafemi Awolowo University agricultural farm. The corncobs were washed with distilled water to remove impurities. The corncobs were dried at room temperature, pulverized, sieved into different particle sizes using standard sieve sizes and stored. Powdered corncobs (PCCS) were separated based on the size. Its micrograph structure, physical and chemical properties were determined using standard methods. The PCCS was used as an adsorbent to remove Pb2+ from aqueous solutions and raw water through batch processes. Effects of the mass of the adsorbent, the initial concentration of Pb2+, initial pH of the aqueous solution and particle size of PCCS on the adsorption kinetics and its models’ parameters were evaluated.
The study shown that moisture content of the PCCS was 7.29 %, volatile solid at 550oC and 1200oC were 96.88 % and 99.44 % respectively. It was also revealed that mass of adsorbent, pH, particle size of the adsorbent, initial concentration of Pb2+ and adsorption time were significant factors that had effects on adsorption of Pb2+ onto PCCS at 95 % confidence level. It was concluded that lead ion can be removed by PCCS, the mass of the adsorbent had significant effects on adsorption kinetics.
- References
- Downloads
- Published
- 2019-04-28
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- A. D. Akinwekomi, I. O. Oladele, A. Oyetunji, Microwave Sintering and Characterisation of Magnesium Alloy AZ61/Carbon Nanotube Composites , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 1 (2019): FUTA Journal of Engineering and Engineering Technology
- SOYOYE Babatunde Oluwamayokun, FALAYI Folayan Richard, OGUNJIMI Jumoke Omowumi, OLORUNFEMI Emmanuel Olasunkanmi, DEVELOPMENT AND PERFORMANCE EVALUATION OF A MOTORIZED BATTERY-POWERED SPRAYER , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 1 (2025): FUTA Journal of Engineering and Engineering Technology
- IDOWU Abimbola Samson , ADEWUYI B.O, FOLORUNSO D.O, AKINWEKOMI A. D., OPTIMUM INFLUENCE OF CHROMIUM AND COMBINE AUSTEMPERING-CRYOGENIC TREATMENTS ON PERFORMANCE OF DUCTILE IRON , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 1 (2025): FUTA Journal of Engineering and Engineering Technology
- R. K. Apalowo, J. A. Kehinde, E. O. Oyeleke, O. J. Owoloja, S. O. Famuyiwa, MACHINE LEARNING OPTIMIZATION OF UNDERFILL FLOW TIME IN FLIP-CHIP ENCAPSULATION OF BGA ASSEMBLIES , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 20 No. 1 (2026): FUTA Journal of Engineering and Engineering Technology
- Talabi H. K. , GREEN SYNTHESIS AND CHARACTERIZATION OF COPPER NANOPARTICLES AS REINFORCEMENT IN EPOXY BASED COMPOSITE USING SPONDIAS MOMBIN LEAF EXTRACT , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 18 No. 2 (2024): FUTA Journal of Engineering and Engineering Technology
- G. A. Fadehan, K. B. Adedeji, K. F. Akingbae, EFFECT OF FREQUENCY NOTCHING TECHNIQUE ON ULTRA-WIDEBAND ANTENNA PERFORMANCE , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 20 No. 1 (2026): FUTA Journal of Engineering and Engineering Technology
- B. Adebayo, Evaluation of the Performance of Atlas Copco SDR4 Rotary Drill In Sagamu Limestone Formation, Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 1 (2019): FUTA Journal of Engineering and Engineering Technology
- S. O. Obayopo, F. J. Banjoko, S. A. Balogun, H. B. Adedayo, Investigation into the Use of Blended Sunflower Oil and Superolein in Hydraulic Systems , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 1 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- Ojo Oluwole Timothy , 2Adeniji Toyosi Adelowokan, DEVELOPMENT OF A BIOMETRIC, FACIAL RECOGNITION AND AUTHENTICATION SYSTEM FOR CLASS ATTENDANCE MANAGEMENT , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 1 (2025): FUTA Journal of Engineering and Engineering Technology
- Obiora-Okeke, O. A, Owolabi, S. H , Adewumi, J. R, HYDRAULIC ASSESSMENT FOR SIGHTING A CONCRETE WEIR ON OGBESE RIVER FOR IRRIGATION , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 18 No. 2 (2024): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.