Equipment Maintenance Management Audit of Some Granite Aggregate Quarries in Part of South - West Nigeria
- Authors
-
-
S. O. Abdulraman
Earth Values Ventures Limited, Taoheed Road, Off Basic ROAD, Ilorin, Nigeria
-
B. M. Olaleye
Department of Mining Engineering, The Federal University of Technology, Akure, Nigeria
-
M. A. Saliu
Department of Mining Engineering, The Federal University of Technology, Akure, Nigeria
-
- Keywords:
- Maintenance management, performance rating, productivity, Granite Quarry
- Abstract
-
This paper analyses an existing maintenance management system in some selected typical granite aggregate quarries (represented as K1, K2 and K3) in part of South- west Nigeria using modied questionnaire and interview. The quarries' current maintenance management effectiveness was evaluated with respect to five basic elements of
maintenance management. The quarries were rated in accordance with global best practices with credits / points ranging from 1 to 3. Investigation shows that K1 and K2 had average overall ratings of 1.45 and 1.39 respectively. These scores fell below average performance, which informed their inability to operate at profit and call for urgent improvement decisions in all elements of maintenance management benchmarked. K3 scored 2.48, which indicates that the quarry adopts an effective maintenance management system, but will also need to improve on its preventive maintenance and maintenance scheduling. This paper is therefore an assessment initiative for maintenance and productivity continuous improvement and can be integrated as a part of a decision support system for maintenance management in the quarry industry. - References
- Downloads
- Published
- 2019-05-03
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- M. K. Adeyeri, Assessment of Maintenance Activities of Some Sawmills in Ekiti and Osun States of Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 1 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- P. M. Enyong, Performance of a Short Transmission Line Module under Various Loads: A Comparative Evaluation , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 2 (2018): FUTA Journal of Engineering and Engineering Technology
- Arowojolu, E.O, Oniyide, G.O, AN ECONOMIC COMPARATIVE ANALYSIS OF EQUIPMENT OUTSOURCING AND OUTRIGHT PURCHASE FOR QUARRYING OPERATIONS AT FOUNTAIN COMPANY, AKURE, ONDO STATE , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 1 (2025): FUTA Journal of Engineering and Engineering Technology
- Olutomilola E. O., Otokola T. O. , Ajayi V. A., DEVELOPMENT OF AN ADJUSTABLE HOPPER FOR HAMMER MILL , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 18 No. 1 (2024): FUTA Journal of Engineering and Engineering Technology
- Ojo Oluwole Timothy , 2Adeniji Toyosi Adelowokan, DEVELOPMENT OF A BIOMETRIC, FACIAL RECOGNITION AND AUTHENTICATION SYSTEM FOR CLASS ATTENDANCE MANAGEMENT , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 1 (2025): FUTA Journal of Engineering and Engineering Technology
- C. N. Udekwe, A. A. Ponnle, A. O. Omolade, EXPERIMENTAL STUDY ON THE SYNERGISTIC EFFECTS OF COOLING METHODS AND HEAT SINK DESIGN ON THERMOELECTRIC GENERATOR PERFORMANCE , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 20 No. Special (2026): FUTA JEET: Special Issue on Innovative Solutions for Sustainable Living and Environmental Challenges: Engineering Perspectives
- B. Adebayo, Evaluation of the Performance of Atlas Copco SDR4 Rotary Drill In Sagamu Limestone Formation, Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 1 (2019): FUTA Journal of Engineering and Engineering Technology
- O. Z. Ayodeji, A. A. Adegun, S. A. Anjorin, DEVELOPMENT AND PERFORMANCE EVALUATION OF A SMALL-SCALE GROUNDNUT SHELLING MACHINE , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 2 (2021): FUTA Journal of Engineering and Engineering Technology
- M. M. Melodi, T. G. Onipede, Economic Appraisal of Some Selected Quarries Operation in Ondo State, Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 2 (2017): FUTA Journal of Engineering and Engineering Technology
- IDOWU Abimbola Samson , ADEWUYI B.O, FOLORUNSO D.O, AKINWEKOMI A. D., OPTIMUM INFLUENCE OF CHROMIUM AND COMBINE AUSTEMPERING-CRYOGENIC TREATMENTS ON PERFORMANCE OF DUCTILE IRON , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 1 (2025): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.