Soil Quality Analysis for Dumpsite Environment in a University Community in Nigeria
- Authors
-
-
C. O. Akinbile
Department of Agricultural & Environmental Engineering, Federal University of Technology, Akure, Nigeria
-
F. O. Ajibade
Department of Civil & Environmental Engineering, Federal University of Technology, Akure, Nigeria
-
O. Ofuafo
Department of Agricultural & Environmental Engineering, Federal University of Technology, Akure, Nigeria
-
- Keywords:
- Waste, Soil, Pollution, Management, University, Nigeria
- Abstract
-
Physicochemical analyses were carried out on soil samples from four different waste dumpsites in the Federal University of Technology Akure (FUTA), Nigeria to ascertain the effects of the refuse dumpsites on soil and groundwater qualities. Dumpsite locations are Physics Laboratory (PHY), Post Graduate Hostel (PG), School of Earth and Mineral Science (SEMS) and Staff Quarters (STQ). Soil samples collected at distances 0 (dumpsite), 10 and 20 m intervals away from the dumpsite were analyzed and at depths 10, 20 and 30 cm. Parameters determined include pH, Electrical Conductivity (EC), Magnesium (Mg), Calcium (Ca), Sodium (Na), Phosphorus (P), Nitrogen (N), Potassium (K), Organic Carbon (OC), Organic Matter (OM) and heavy metals such as Copper (Cu) and Lead (Pb) and subjected to relevant statistical analysis. Most of the parameters analyzed indicated pollution and were below the Food and Agricultural Organization (FAO) limits. P and Mg concentrations ranged from 1.19 to 1.25mg/kg and 3.17 to 13.61mg/kg respectively which indicated pollution. Out of heavy metals analyzed, Cu was 1.75mg/kg and Pb was not detected. Statistical analysis indicated significant differences at 95% level. The result showed that the soil samples were mildly polluted and therefore not suitable for crop production.
- Author Biography
- References
- Downloads
- Published
- 2019-05-03
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- M. M. Melodi, T. G. Onipede, Economic Appraisal of Some Selected Quarries Operation in Ondo State, Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 2 (2017): FUTA Journal of Engineering and Engineering Technology
- M. M. Melodi, D. A. Agboola, Labour Productivity Assessment of Dredging Operations in Some Selected Companies in Lagos State, Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 1 (2017): FUTA Journal of Engineering and Engineering Technology
- M. M. Melodi, O. S. Adekinya, Assessment of Cost Effectiveness of Borehole Drilling in Oyo State, Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 10 No. 1 (2016): FUTA Journal of Engineering and Engineering Technology
- C. M. Ikumapayi, C. Arum, Pozzolanic Influence of Bagasse Ash on the Compressive Strength and Dry Shrinkage of Concrete , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 2 (2019): FUTA Journal of Engineering and Engineering Technology
- A. O. Melodi, B. O. Akinloye, Transmission Capacity Enhancement for Nigerian Power Transmission Grid using TCSC and UPFC , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 8 No. 2 (2014): FUTA Journal of Engineering and Engineering Technology
- Oluwatoyin Olaseinde, O. Ajanaku, O. M. Ojo, S. O. Seidu, COMPARATIVE STUDY OF THE REINFORCED STEEL BARS OBTAINED FROM A FAILED RESIDENTIAL BUILDING AND THE SHELVES , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 2 (2021): FUTA Journal of Engineering and Engineering Technology
- E. O. Aiyewalehinmi, O. S. Aderinola, Strength Properties of Commercially Produced Sandcrete block in Ikeja: Lagos State , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 9 No. 1 (2015): FUTA Journal of Engineering and Engineering Technology
- Anthony T. Bolarinwa, Gideon C. Nwafor, OPEN PIT OPTIMIZATION AND PRODUCTION SCHEDULING OF OKOBO COAL MINE, CENTRAL NIGERIA , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 1 (2018): FUTA Journal of Engineering and Engineering Technology
- J. J. Popoola, D. O. Akinfenwa, I. O. Animasahun, Assessment of Electromagnetic Radiation Effects and Safety Issues of GSM-900 and GSM-1800 Radio Frequencies – A Case Study of Akure, Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 9 No. 1 (2015): FUTA Journal of Engineering and Engineering Technology
- N G Olaiya, P K Farayibi, P K Oke, A REVIEW ON ADDITIVE MANUFACTURING: LASER TECHNOLOGY METHODS, DISTINCTIONS AND APPLICATIONS IN MANUFACTURING ENGINEERING , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 2 (2018): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.