Soil Quality Analysis for Dumpsite Environment in a University Community in Nigeria
- Authors
-
-
C. O. Akinbile
Department of Agricultural & Environmental Engineering, Federal University of Technology, Akure, Nigeria
-
F. O. Ajibade
Department of Civil & Environmental Engineering, Federal University of Technology, Akure, Nigeria
-
O. Ofuafo
Department of Agricultural & Environmental Engineering, Federal University of Technology, Akure, Nigeria
-
- Keywords:
- Waste, Soil, Pollution, Management, University, Nigeria
- Abstract
-
Physicochemical analyses were carried out on soil samples from four different waste dumpsites in the Federal University of Technology Akure (FUTA), Nigeria to ascertain the effects of the refuse dumpsites on soil and groundwater qualities. Dumpsite locations are Physics Laboratory (PHY), Post Graduate Hostel (PG), School of Earth and Mineral Science (SEMS) and Staff Quarters (STQ). Soil samples collected at distances 0 (dumpsite), 10 and 20 m intervals away from the dumpsite were analyzed and at depths 10, 20 and 30 cm. Parameters determined include pH, Electrical Conductivity (EC), Magnesium (Mg), Calcium (Ca), Sodium (Na), Phosphorus (P), Nitrogen (N), Potassium (K), Organic Carbon (OC), Organic Matter (OM) and heavy metals such as Copper (Cu) and Lead (Pb) and subjected to relevant statistical analysis. Most of the parameters analyzed indicated pollution and were below the Food and Agricultural Organization (FAO) limits. P and Mg concentrations ranged from 1.19 to 1.25mg/kg and 3.17 to 13.61mg/kg respectively which indicated pollution. Out of heavy metals analyzed, Cu was 1.75mg/kg and Pb was not detected. Statistical analysis indicated significant differences at 95% level. The result showed that the soil samples were mildly polluted and therefore not suitable for crop production.
- Author Biography
- References
- Downloads
- Published
- 2019-05-03
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- A. A. Ponnle, S. K. Ani, Assessment of Exposure to Indoor Power Frequency Magnetic Fields: SEET Building and Engineering Laboratories, FUTA , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 1 (2019): FUTA Journal of Engineering and Engineering Technology
- T. S. Mogaji, A. Akinsade, M. A. Akintunde, Pyrolysis of Sugarcane Bagasse for Bio-Oil Production , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 2 (2019): FUTA Journal of Engineering and Engineering Technology
- Samuel Olusola Olatunji, An Assessment of the Barriers of Timely Payment in Public Building Projects in Ekiti State, Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 1 (2019): FUTA Journal of Engineering and Engineering Technology
- J. A. Afelumo, O. A. Ademeso, Investigation of the Integrity of Subsoil as Foundation Support for a new Hostel Building, FUT, Akure, Southwestern Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 2 (2019): FUTA Journal of Engineering and Engineering Technology
- Abdulwahab J. Yusuf, A. A. Olaniyan, A Modified Droop Controller for Micro-Grid Power Quality Improvement Using Artificial Fish Swarm Algorithm (AFSA) , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 2 (2018): FUTA Journal of Engineering and Engineering Technology
- O. O. Olubanjo, Effects of Wastewaters From an Abattoir on Surface Water Quality in Akure, Ondo State, Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 1 (2017): FUTA Journal of Engineering and Engineering Technology
- M. K. Adeyeri, Assessment of Maintenance Activities of Some Sawmills in Ekiti and Osun States of Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 1 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- P. M. Enyong, Performance of a Short Transmission Line Module under Various Loads: A Comparative Evaluation , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 2 (2018): FUTA Journal of Engineering and Engineering Technology
- I. O. Oladele, O. O. Daramola, A. Oyetunji, Appropriate Technological Procedures for Fusion Welding of Low Alloy Carbon Steel , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 8 No. 1 (2014): FUTA Journal of Engineering and Engineering Technology
- B. O. Akinnuli, S. P Ayodeji, S. O. Abadariki, J. O. Fasan, Design, Fabrication and Performance Evaluation of a Reciprocating Cocoa Pod Breaking Machine , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 8 No. 1 (2014): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.