Soil Quality Analysis for Dumpsite Environment in a University Community in Nigeria
- Authors
-
-
C. O. Akinbile
Department of Agricultural & Environmental Engineering, Federal University of Technology, Akure, Nigeria
-
F. O. Ajibade
Department of Civil & Environmental Engineering, Federal University of Technology, Akure, Nigeria
-
O. Ofuafo
Department of Agricultural & Environmental Engineering, Federal University of Technology, Akure, Nigeria
-
- Keywords:
- Waste, Soil, Pollution, Management, University, Nigeria
- Abstract
-
Physicochemical analyses were carried out on soil samples from four different waste dumpsites in the Federal University of Technology Akure (FUTA), Nigeria to ascertain the effects of the refuse dumpsites on soil and groundwater qualities. Dumpsite locations are Physics Laboratory (PHY), Post Graduate Hostel (PG), School of Earth and Mineral Science (SEMS) and Staff Quarters (STQ). Soil samples collected at distances 0 (dumpsite), 10 and 20 m intervals away from the dumpsite were analyzed and at depths 10, 20 and 30 cm. Parameters determined include pH, Electrical Conductivity (EC), Magnesium (Mg), Calcium (Ca), Sodium (Na), Phosphorus (P), Nitrogen (N), Potassium (K), Organic Carbon (OC), Organic Matter (OM) and heavy metals such as Copper (Cu) and Lead (Pb) and subjected to relevant statistical analysis. Most of the parameters analyzed indicated pollution and were below the Food and Agricultural Organization (FAO) limits. P and Mg concentrations ranged from 1.19 to 1.25mg/kg and 3.17 to 13.61mg/kg respectively which indicated pollution. Out of heavy metals analyzed, Cu was 1.75mg/kg and Pb was not detected. Statistical analysis indicated significant differences at 95% level. The result showed that the soil samples were mildly polluted and therefore not suitable for crop production.
- Author Biography
- References
- Downloads
- Published
- 2019-05-03
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- A. R. Iyanda, O. A. Odejobi, Computational Modelling Technique for Short-Term Electric Load Forecasting , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 9 No. 2 (2015): FUTA Journal of Engineering and Engineering Technology
- J. A.V. Famurewa, E. T. Faboya, The Effects of Drying Temperature on the Physicochemical Properties of Ogbono (lrvingia Gabonensis) , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 1 (2017): FUTA Journal of Engineering and Engineering Technology
- T A EWEMOJE, S D FAGBAYIDE, K O OLUWASEMIRE, LYSIMETER DETERMINATION OF CROP COEFFICIENT OF DRIP IRRIGATED JATROPHA CURCAS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 1 (2018): FUTA Journal of Engineering and Engineering Technology
- Samuel L Akingbonmire, L Samuel, O Oluwafemi Omotayo, J O Afolayan, A Banjo Olorunshola, THE PHYSICO-CHEMICAL PROPERTIES OF SOME FINE AGGREGATES IN LOKOJA, NIGERIA , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 2 (2018): FUTA Journal of Engineering and Engineering Technology
- Kayode Francis Akingbade, DEVELOPMENT OF CHEMICAL PROPORTION FORMULATION MODEL FOR QUALITY CONTROL IN FLEXIBLE POLYURETHANE FOAM PRODUCTION , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 2 (2018): FUTA Journal of Engineering and Engineering Technology
- Olufemi Adeyemi Adetola, M. J. Odu, THE DEVELOPMENT OF A HAND-PUSH WEEDER FOR CUTTING WEEDS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 2 (2021): FUTA Journal of Engineering and Engineering Technology
- Folasade Dahunsi, Oluwasina Aderinwale, Abayomi Adesida, Abiola Alayande, J. Ojo, Oluwaseyi Falola, Oluwarotimi Dahunsi, DEVELOPMENT OF A SPACE TECHNOLOGY CAPACITY BUILDING INITIATIVE AT THE FEDERAL UNIVERSITY OF TECHNOLOGY, AKURE, NIGERIA , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 1 (2021): FUTA Journal of Engineering and Engineering Technology
- M O Idris, EVALUATION OF EFFECTS OF EXTERNAL FACTORS ON DUE DATES PREDICTION IN MANUFACTURING JOBSHOPS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 2 (2018): FUTA Journal of Engineering and Engineering Technology
- B. Adebayo, Evaluation of the Performance of Atlas Copco SDR4 Rotary Drill In Sagamu Limestone Formation, Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 1 (2019): FUTA Journal of Engineering and Engineering Technology
- Babatunde Oluwamayokun Soyoye, Tehinse, T. O., Design and Fabrication of a Maize Shelling Machine , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 2 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
You may also start an advanced similarity search for this article.