The Effects of Drying Temperature on the Physicochemical Properties of Ogbono (lrvingia Gabonensis)
- Authors
-
-
J. A.V. Famurewa
Department of Food Science and Technology Federal University of Technology, Akure, Ondo State, Nigeria
-
E. T. Faboya
Department of Food Science and Technology, Rufus Giwa Polytechnic Owo, Ondo State, Nigeria
-
- Keywords:
- Functional properties, Proximate Compositions, Mineral Contents, Drying, Ogbono
- Abstract
-
The kernel seed flour of Ogbono (Irvingia gabonensis) was screened to test for the effects of drying temperatures on its physicochemical properties in order to evaluate its final qualities. Sorted and cleaned 'Ogbono' kernel seeds were splitted into two equal halves for uniform drying, weighed and dried at 50, 60 and 70°C. Weights of the samples were monitored at interval of one hour until constant weights were achieved. Analyses of the flour samples were carried out using analytical grade reagents. Proximate composition of the samples showed no significant difference at (p< 0.05) and ranged from 3.5 to 4.0, 1.99 to 3.24, 52.49 to 56.73, 1.86 to 2.62 and 33.86 to 38.71 for moisture content,protein, crude fat, total ash and carbohydrate respectively, this implies that Ogbono kernel seeds can be dried at any temperature within 50 to 70 °C without any appreciable loss of proximate values. The trend of the results showed decrease in the values of fat content but ash and carbohydrate content increase with increase in drying temperatures, low fat diet is recommended for both young and elderly people. Higher values were also recorded for mineral composition of the sample dried at 70 °C; 7.80, 194, 10.5 and 29.80/or Na, K, Ca and Fe respectively. The same sample also possessed relatively highest bulk density (0.60 g/cm3) which is important in relation to packaging efficiency. However sample dried at 50 °C is more viscous. Water and oil absorption capacities of the samples also decreased with increase in drying temperature which implies that more quantity will be needed when used as a thickener in food formulation for samples dried at higher air- drying temperatures. Drying temperature o/70 °C was therefore recommended to produce Ogbono flour of high chemical qualities.
- References
- Downloads
- Published
- 2019-05-04
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- T. S. Mogaji, A. Akinsade, M. A. Akintunde, Pyrolysis of Sugarcane Bagasse for Bio-Oil Production , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 2 (2019): FUTA Journal of Engineering and Engineering Technology
- C. O. Ijagbemi, D. T. Oloruntoba, A. O. Adeoye, Development of a Bioplastic Film for Food Packaging , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 8 No. 1 (2014): FUTA Journal of Engineering and Engineering Technology
- E. O. Ajaka, O. C. Chukwuma, Promax2100: A Computer Programme for Design and Optimization of Mineral Processing Plant , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 8 No. 1 (2014): FUTA Journal of Engineering and Engineering Technology
- A. S. Oyerinde, EFFECT OF DRYING RATE AND MOISTURE REMOVAL ON THE DRYING PROPERTIES OF GROUND AND FERMENTED CASSAVA MASH ("GARI") , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 1 (2021): FUTA Journal of Engineering and Engineering Technology
- Samuel L Akingbonmire, L Samuel, O Oluwafemi Omotayo, J O Afolayan, A Banjo Olorunshola, THE PHYSICO-CHEMICAL PROPERTIES OF SOME FINE AGGREGATES IN LOKOJA, NIGERIA , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 2 (2018): FUTA Journal of Engineering and Engineering Technology
- A. S. Taiwo, I. O. Oladele, O. O. Daramola, A. D. Akinwekomi, O. G. Agbabiaka, Mechanical Wear Resistance and Water Absorption Properties of Particulate Palm Kernel Shell Reinforced Epoxy Composites for Automobile Application , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 1 (2019): FUTA Journal of Engineering and Engineering Technology
- J. Isa, M. A. Aderotoye, Effect of moisture content on the physical and aerodynamics properties of cashew nut , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 2 (2017): FUTA Journal of Engineering and Engineering Technology
- F I OTU, E I BELLO, T I OGEDENGBE, L LAJIDE, FOURIER TRANSFORM INFRARED SPECTROSCOPIC ANALYSIS OF RUBBER SEED OIL AND ITS BIODIESEL , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 1 (2018): FUTA Journal of Engineering and Engineering Technology
- P. B. Mogaji, T. E. Abioye, N. O. Ohuruogu, Development of Epoxy Resin Composite Reinforced With Cow Horn and Cassava Particles for Car Dashboard , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 1 (2017): FUTA Journal of Engineering and Engineering Technology
- A. J. Abegunde, B. V. Omidiji, P. O. Ajewole, Characterization of Ado-Ekiti River Sand for foundry applications , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 2 (2017): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.