Development of an Improved Vapour Compression Refrigeration System for Preservation of fresh Vegetables
- Authors
-
-
T. S. Mogaji
Department of Mechanical Engineering, Federal University of Technology, Akure
-
- Keywords:
- Vapour compression refrigerator system, Temperature control device, temperature, relative humidity, bitter leaf, pumpkin leaf
- Abstract
-
An improved vapour compression refrigeration system (VCRS) was developed for the preservation of fresh vegetables and its performance was evaluated. The cooling system operating with R134a as working fluid consists of an evaporator, compressor, condenser, capillary tube and a redesigned temperature control device (TCD). The refrigeration system has capacity to accommodate 0.02 metric tonnes (20 kg) of any fresh vegetables. The improved cooling system was used to preserve fresh vegetables such as: bitter leaf (Vernonia amygdalina Delile) and pumpkin leaf (Telfairia occidentalis). Study was conducted to check the freshness of the vegetables and data were observed daily. Results of the transient performance tests revealed that an average cabinet and ambient temperature of 3.64C and 26.89C were observed, and an average cabinet and ambient relative humidity of 94.50% and 45.23% were recorded respectively for the preserved vegetables. The needed optimum storage temperature range for the preservation of the selected vegetables samples were attained in cooling system at 2C – 4C with the aids of the incorporated newly designed TDC. The improved domestic vapour compression refrigeration system performed up to expectation as the shelf life of the tested sample inside the cooling system was extended by fourteen days relative to ambient storage.
- References
- Downloads
- Published
- 2019-05-14
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- O O. Daramola, MECHANICAL PROPERTIES AND WEAR BEHAVIOUR OF KAOLINITE CLAY PARTICLES REINFORCED EPOXY MATRIX COMPOSITES , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 2 (2021): FUTA Journal of Engineering and Engineering Technology
- Kayode Francis Akingbade, DEVELOPMENT OF CHEMICAL PROPORTION FORMULATION MODEL FOR QUALITY CONTROL IN FLEXIBLE POLYURETHANE FOAM PRODUCTION , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 2 (2018): FUTA Journal of Engineering and Engineering Technology
- Ashiru Mohammed, Ibrahim Aliyu, Hussaini Abdullahi Umar, Aliyu Umar Mani, PERFORMANCE EVALUATION OF RAILWAY BALLAST DEGRADATION USING THE MORPHOLOGICAL PROPERTIES , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 2 (2021): FUTA Journal of Engineering and Engineering Technology
- I O OLADELE, O O DARAMOLA, A M OKORO, J A OMOTOYINBO, EVALUATION OF THE EFFECT OF MERCERIZED WHITE CHICKEN FEATHER FIBRES ON THE MECHANICAL , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 1 (2018): FUTA Journal of Engineering and Engineering Technology
- I. O. Oladele, O. G. Agbabiaka, O. S. Akinola, H. K. Talabi, Development of Sponge Fiber and Particulate Palm Kernel Shell Ash Reinforced Polypropylene Hybrid Composites , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 10 No. 2 (2016): FUTA Journal of Engineering and Engineering Technology
- J. J. Popoola, D. O. Akinfenwa, I. O. Animasahun, Assessment of Electromagnetic Radiation Effects and Safety Issues of GSM-900 and GSM-1800 Radio Frequencies – A Case Study of Akure, Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 9 No. 1 (2015): FUTA Journal of Engineering and Engineering Technology
- K D Adedayo, T Ewetumo, I Konwea, T Ewetumo, DEVELOPMENT OF A LOW COST MICROCONTROLLER - BASED HAEMOGLOBIN METER , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 2 (2018): FUTA Journal of Engineering and Engineering Technology
- Olufemi Adeyemi Adetola, M. J. Odu, THE DEVELOPMENT OF A HAND-PUSH WEEDER FOR CUTTING WEEDS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 2 (2021): FUTA Journal of Engineering and Engineering Technology
- T A EWEMOJE, S D FAGBAYIDE, K O OLUWASEMIRE, LYSIMETER DETERMINATION OF CROP COEFFICIENT OF DRIP IRRIGATED JATROPHA CURCAS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 1 (2018): FUTA Journal of Engineering and Engineering Technology
- A. S. Oyerinde, EFFECT OF DRYING RATE AND MOISTURE REMOVAL ON THE DRYING PROPERTIES OF GROUND AND FERMENTED CASSAVA MASH ("GARI") , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 1 (2021): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.