NEWTON RAPHSON SOLUTIONS OF BIOCHEMICAL OXYGEN DEMAND (BOD) KINETICS
- Authors
-
-
J. O. BABAJIDE
Department of Civil Engineering, Obafemi Awolowo University, Ile-Ife, Nigeria
-
E. O. FEHINTOLA
Department of Chemistry, Adeyemi Federal University of Education, Ondo, Nigeria;
-
T. A. ALADESANMI
Information Technology and Communications Unit, Obafemi Awolowo University, Ile- Ife, Nigeria
-
M. D. IDI
Land, Air and Water Consulting, F6 Ibrahim Taiwo Estate, Baga Road, Maiduguri, Borno State, Nigeria
-
E. A. ADEKUNBI
Department of Chemistry, Adeyemi Federal University of Education, Ondo, Nigeria;
-
I. A. OKE
Department of Civil Engineering, Obafemi Awolowo University, Ile-Ife, Nigeria
-
E. O. OBIJOLE
Department of Chemistry, Adeyemi College of Education, Ondo
-
- Keywords:
- Wastewater, BOD kinetics, Newton- Raphson method, methods of determining BOD rate, total error, CD MSC, statistical reliability
- Abstract
-
As follow up on our previous studies, this paper evaluated Newton-Raphson method (NRM) solutions of Biochemical Oxygen Demand (BOD) kinetics with the aim of ascertain error free solutions. Non-linear regression, logarithms difference, NRM, least square, daily difference, Thomas, two points, ratio and Fujimoto methods were used to determine constants in BOD kinetics. Microsoft Excel Solver was applied to all the methods. Accuracies of all the methods were evaluated using relative error, Coefficient of Determination (CD), reliability and Model of Selection Criterion (MSC). The study revealed that the values of ultimate BOD and BOD removal rate were in the range of 859 to 1911 mg/l and - 0.140/d to - 0.449 /d respectively. Average total error for the methods were 23.85, 25.7, 74.72, 88.68, 1066.5, 1016.33, 149.12, 78.1 and (61.45 and 59.10) for non-liner regression, logarithms difference, least squares, Thomas, Fujimoto, Ratio, two points, daily difference and NRM ( matrix and graphical).
Accuracy, validity and good fitness of these methods were in order of non-linear regression (8.16) > Logarithm difference (7.72) > NRM (6.26) > least square (6.03) >daily difference (5.42)> Thomas (5.04)> two points (4.14) > ratio (0.63) and Fujimoto (0.51) on basis of their average MSC values. It was concluded that NRM could be used for BOD kinetics. NRM is among the best options because of their simplicity and flexibility as graphical and numerical solutions.
- References
- Downloads
- Published
- 2020-04-03
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- M. D. IDI, T. A. ALADESANMI, S. LUKMAN, M. A. ASANI, Y. M. USMAN, I. A. OKE, A NUMERICAL FORMULA AND COST BENEFIT OF GROUNDWATER RECHARGE IN MAIDUGURI, NIGERIA , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 2 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- O. O. Olubanjo, Effects of Wastewaters From an Abattoir on Surface Water Quality in Akure, Ondo State, Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 1 (2017): FUTA Journal of Engineering and Engineering Technology
- A. P. Olalusi, M. S. Obot, A. S. Ogunlowo, Modelling the Dehydration Characteristics of Taro (Colocasia Esculenta) Slices in a Convective Cabinet Dryer , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 8 No. 1 (2014): FUTA Journal of Engineering and Engineering Technology
- Adebayo Felix Owa, Daniel Toyin Oloruntoba, Muideen Adebayo Bodude, Fisayo Adesina, INVESTIGATION OF MILD STEEL PROTECTION WITH GLASS WOOL IN CORROSIVE MEDIA , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 2 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- Samuel Olugbenga Oladele, MODELLING OF THIN-LAYER MICROWAVE DRYING OF BITTER LEAF SAMPLES (Vernonia Amygdalina) FOR PRESERVATION , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 1 (2018): FUTA Journal of Engineering and Engineering Technology
- O.A. ADEMESO, B.I. ADEYEMO, Physical and Mechanical Characteristics of the Conglomeratic Layer in Akure, Southwestern Nigeria. , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 2 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- O OLANIRAN, J O BORODE, A E AFOLABI, P A OLUBAMBI, B A OLANIRAN, D O FOLORUNSO, CORROSION ASSESSMENT OF SINTER DUPLEX STAINLESS STEEL COMPOSITES IN PINEAPPLE JUICE EXTRACT , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 1 (2018): FUTA Journal of Engineering and Engineering Technology
- Adebayo Felix Owa, Abdulahi Olawale Adebayo, Olawale Olarewaju Ajibola, Oluwole Daniel Adigun, Sunday Gbenga Aborisade, Fisayo Adesina, Corrosion Behaviour of Low Carbon Steel in Sulphide Medium Using Thevetia Peruviana as Inhibitor , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 2 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- E. O. Ajaka, O. E. Abiodun, Determining The Metal Contents of Leach Liqour from Ihietutu Lead and Zinc Ore, Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 1 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- A D Dada, BRIDGING RESEARCH-INDUSTRY DIVIDE IN FOOD AND BEVERAGE ENTERPRISES: EMPIRICAL EVIDENCE FROM SOUTHWESTERN NIGERIA , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 1 (2018): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.