MECHANICAL PROPERTIES OF EPOXY MATRIX COMPOSITES REINFORCED WITH GARLIC PARTICLES
- Authors
-
-
O. O. Daramola
3Department of Metallurgical and Materials Engineering, Federal University of Technology, Akure, PMB 704, Nigeria
-
I. O. Oladele
Department of Metallurgical and Materials Engineering, Federal University of Technology, Akure, PMB 704, Nigeria
-
O. S. AKINTAYO
Department of Metallurgical and Materials Engineering, Federal University of Technology, Akure, PMB 704, Nigeria
-
- Keywords:
- Epoxy resin, Garlic, Submicron particles, Mechanical properties, Composite
- Abstract
-
Epoxy resin with different weight fractions of submicron garlic particles were used to develop epoxy composites. Mechanical properties (tensile, flexural and impact) of the developed composites were characterized. The microstructure of tensile fractured surfaces was examined by Scanning Electron Microscope (SEM) in order to identify the relevant fracture modes involved. Results showed that the tensile strength, tensile modulus, flexural strength, flexural stiffness and impact strength was enhanced in the composites with the tensile strength, tensile modulus and impact strength experiencing peak values at 8 wt.% garlic loading before decreasing. Flexural strength and stiffness increased in a linear mode while elongation at break was found to reduce slightly in the composites when compared to the neat epoxy resin. Microstructure revealed the brittle nature of the neat epoxy. Individual particles with low degree of aggregation were observed in the composites with lower loading. However, particles agglomeration was observed in the highly filled composite (10 wt% garlic) resulting in the termination of the linear increase experienced in the tensile strength, tensile modulus and impact strength results. Overall, the test results demonstrate the competency of garlic particles to serve as a reliable, cost effective and efficient reinforcement material for the development of epoxy reinforced composites.
- References
- Downloads
- Published
- 2025-12-08
- Section
- Articles
- License
-
Copyright (c) 2021 FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY

This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- O. O. Awopetu, Cyclical Chips Formation during Machining of Titanium and Titanium Alloys , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 10 No. 1 (2016): FUTA Journal of Engineering and Engineering Technology
- A Amoko, S JUSTINAH, A Fehintola, O Ezekiel, I Oke, A Isaiah, EVALUATION OF EFFECTS OF SELECTED FACTORS ON ADSORPTION KINETICS OF LEAD ION REMOVAL FROM AQUEOUS SOLUTIONS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 2 (2018): FUTA Journal of Engineering and Engineering Technology
- K.O. OLADOSU, E.O. OLAFIMIHAN, O.R. OYETUNJI, M.O. ADEOTI, A.A. ADEJARE, Influence of Kaolin Additive on Ash Yield of Palm Kernel-Cashew Shell Combustion: Effect of Kaolin Additive on Ash Yield of Palm Kernel- Cashew Shell Combustion , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 2 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- S. A. Alabi, I. A. Arighaye, J. O. Afolayan, PROGRESSIVE FAILURE ANALYSIS OF MULTI-STOREY REINFORCED CONCRETE BUILDINGS UNDER DIFFERENTIAL SETTLEMENT , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 1 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- M O Idris, EVALUATION OF EFFECTS OF EXTERNAL FACTORS ON DUE DATES PREDICTION IN MANUFACTURING JOBSHOPS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 2 (2018): FUTA Journal of Engineering and Engineering Technology
- J. T. Fasinmirin, A. J. Adesigbin, Tillage Effects on Some Soil Physical Properties and Yield of Cowpea (Vigna unguiculata) in the Humid Rain Forest of Akure, Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 9 No. 2 (2015): FUTA Journal of Engineering and Engineering Technology
- F. M. Dahunsi, S. O. Oluponna, Analysis of Energy Usage Pattern of a Nigerian University Digital Resource Center (DRC):: FUTA DRC as a Case Study , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 2 (2019): FUTA Journal of Engineering and Engineering Technology
- A. S. Abubakar, Y. A. Sha'aban, Multiple Model Predictive Control for DFIG Based Wind Energy Conversion System , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 1 (2019): FUTA Journal of Engineering and Engineering Technology
- J. O. Amigun, Seismic Inverted Acoustic Impedance for Lithofacies Discrimination and Reservoir Fluids Prediction: A Case of ‘Ovi’ Field, Niger Delta , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 2 (2019): FUTA Journal of Engineering and Engineering Technology
- C. O. Ijagbemi, Design and Optimization of A Gas Turbine Waste Heat Recovery System , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 2 (2019): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.
