ASSESSMENT OF GROUNDNUT SHELL ASH AND SAWDUST ASH AS PARTIAL REPLACEMENT OF CEMENT IN CONCRETE
- Authors
-
-
Tasiu Ashiru Sulaiman
Ahmadu Bello University, Zaria
-
Ibrahim Aliyu
-
Yusuf Yau
-
Ibrahim Bello
-
- Keywords:
- Groundnut Shell Ash (GSA), Sawdust Ash (SDA), workability, compressive strength, and pozzolana
- Abstract
-
This study is aimed at evaluating the combined effect of groundnut shell ash and sawdust ash (GSA/SDA) as partial replacement of ordinary Portland cement in concrete using 1:2:4 mix ratio. The ashes were obtained by the uncontrolled burning process and ground after cooling, the burnt ash was passed through a 75 microns BS sieve. Cement was replaced with 0%, 5%, 10%, 15%, and 20% of GSA/SDA and a water-cement ratio of 0.6 was used. Concrete cubes of 100mm x 100mm x 100mm were cast and cured in water for 3, 14, 21 and 28 days respectively. The result of workability shows that as the GSA/SDA content increased the workability (slump) decreased, but setting times and soundness of GSA/SDA-cement paste increases as the GSA/SDA content increases. However, the compressive strength of GSD/SDA-concrete increases as the curing age increases, and it also increases as the GSD/SDA content increases up to 10% at 28 days then decreases. Finally, it can be concluded that SDA is suitable material for use as a pozzolan since it satisfied the requirement for such a material by having a combined (SiO2+ Al2O3 + Fe2O3) of more than 70%, which was classified as a class C pozzolana, while GSA is a low reactive pozzolan and the optimum percentage of the GSA/SDA to be used should not be more than 10% replacement.
- References
- Downloads
- Published
- 2020-11-18
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- B. Adebayo, Evaluation of the Performance of Atlas Copco SDR4 Rotary Drill In Sagamu Limestone Formation, Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 1 (2019): FUTA Journal of Engineering and Engineering Technology
- E. O. Aiyewalehinmi, O. S. Aderinola, Strength Properties of Commercially Produced Sandcrete block in Ikeja: Lagos State , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 9 No. 1 (2015): FUTA Journal of Engineering and Engineering Technology
- I. O. Oladele, O. G. Agbabiaka, O. S. Akinola, H. K. Talabi, Development of Sponge Fiber and Particulate Palm Kernel Shell Ash Reinforced Polypropylene Hybrid Composites , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 10 No. 2 (2016): FUTA Journal of Engineering and Engineering Technology
- O. Z. Ayodeji, A. A. Adegun, S. A. Anjorin, DEVELOPMENT AND PERFORMANCE EVALUATION OF A SMALL-SCALE GROUNDNUT SHELLING MACHINE , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 2 (2021): FUTA Journal of Engineering and Engineering Technology
- O.A. ADEMESO, B.I. ADEYEMO, Physical and Mechanical Characteristics of the Conglomeratic Layer in Akure, Southwestern Nigeria. , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 2 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- Dafiewhare, O, Ijagbemi, C. O, Ologunwa, T. P, Alabi, O. T, Ijagbemi, A. O, PRODUCTION AND EVALUATION OF BIOMASS BRIQUETTES FROM PALM KERNEL SHELL AND COCONUT HUSK , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 2 (2025): FUTA Journal of Engineering and Engineering Technology
- A. J. Abegunde, B. V. Omidiji, P. O. Ajewole, Characterization of Ado-Ekiti River Sand for foundry applications , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 2 (2017): FUTA Journal of Engineering and Engineering Technology
- Aderinola, O.S, Ata, G.O, ENHANCING ASPHALT PAVEMENT PERFORMANCE THROUGH PALM KERNEL SHELLS (PKS) INTEGRATION , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 19 No. 1 (2025): FUTA Journal of Engineering and Engineering Technology
- C. O. Ijagbemi, D. T. Oloruntoba, A. O. Adeoye, Development of a Bioplastic Film for Food Packaging , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 8 No. 1 (2014): FUTA Journal of Engineering and Engineering Technology
- O. O. Daramola, I. O. Oladele, O. S. AKINTAYO, MECHANICAL PROPERTIES OF EPOXY MATRIX COMPOSITES REINFORCED WITH GARLIC PARTICLES , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 2 (2021): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.