PROGRESSIVE FAILURE ANALYSIS OF MULTI-STOREY REINFORCED CONCRETE BUILDINGS UNDER DIFFERENTIAL SETTLEMENT
- Authors
-
-
S. A. Alabi
Department of Civil Engineering, the Federal University of Technology, Akure, Nigeria
-
I. A. Arighaye
Ondo State Ministry of Works, Department of Planning, Design, Research and Statistics, Akure, Nigeria
-
J. O. Afolayan
Department of Civil Engineering, the Federal University of Technology, Akure, Nigeria
-
- Keywords:
- Progressive failure, demand-capacity ratio, differential settlement, multiÂ-storey building, alternative load path method
- Abstract
-
Multi-Storey buildings are buildings with many floors above the ground floor, which serve as shelters for man, his properties and activities. Most building/ails because they were only designed for normal loads whereas abnormal loads were not considered. Therefore, this paper investigates the potential for progressive failure of multi-storey reiriforced concrete (RC) buildings under chosen varying degrees of settlement ranging between 2 5 mm and 15 0 mm. The computer-based modelling procedure following Alternative Load Path Method is adopted for progressive failure analysis. A 5-typical frame models based on the beams' cross-sectional dimensions were analyzed. Each of the frames is analyzed under the normal loads, combining with the assumed differential settlement. From the results obtained, it is discovered that the potential for progressive failure of a multi-storey RC building increases with the increase in the degree of differential settlement. At 25 mm to 75 mm settlement, vulnerability to progressive failure is very low as the Demand-Capacity-Ratio (DCR) values of the component members are very small, but from I 00 mm settlement and above the structure exhibits high potential for progressive failure. It is also noted that the potential for progressive failure of the structure decreases upwards the building storeys. The potential for progressive failure is higher in the lower floors than in the upper floors. Also, the rigidity of the structure helps in combating progressive failure under differential settlement.
- References
- Downloads
- Published
- 2020-04-09
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- M. A. Akintunde, K A ADETORO, T. J. Abioye, Development of Refrigeration System for Storage and Preservation of Yam Tubers , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 2 (2019): FUTA Journal of Engineering and Engineering Technology
- T. S. Mogaji, Development of an Improved Vapour Compression Refrigeration System for Preservation of fresh Vegetables , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 1 (2019): FUTA Journal of Engineering and Engineering Technology
- J.A. GBADEYAN, O.T. OLOTU, NATURAL VIBRATION ANALYSIS OF A TAPERED ROTATING PRESTRESSED RAYLEIGH BEAM USING DIFFERENTIAL TRANSFORM METHOD , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 2 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- M. M. Melodi, D. A. Agboola, Labour Productivity Assessment of Dredging Operations in Some Selected Companies in Lagos State, Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 1 (2017): FUTA Journal of Engineering and Engineering Technology
- A. P. Olalusi, M. S. Obot, A. S. Ogunlowo, Modelling the Dehydration Characteristics of Taro (Colocasia Esculenta) Slices in a Convective Cabinet Dryer , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 8 No. 1 (2014): FUTA Journal of Engineering and Engineering Technology
- O. Adukwu, E. D. Oku, O. I. Apeh, Bivariate Empirical Modeling of Global System for Mobile-Communication (GSM) Propagation Path Loss in an Undulating Terrain , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 2 (2018): FUTA Journal of Engineering and Engineering Technology
- P. B. Mogaji, O. A. Raimi, Determination of Optimum Parameters for Drilling Stainless Steel using Response Surface Methodology (RSM) , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 10 No. 1 (2016): FUTA Journal of Engineering and Engineering Technology
- D. J. Afu, E. O. Ifelola, S. G. Ayodele, A. Ekun, A. Itunu, Survey of the Effects of Operational Noise on Quarry Workers in Akoko-Edo Local Government Area of Edo State , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 2 (2017): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.