PROGRESSIVE FAILURE ANALYSIS OF MULTI-STOREY REINFORCED CONCRETE BUILDINGS UNDER DIFFERENTIAL SETTLEMENT
- Authors
-
-
S. A. Alabi
Department of Civil Engineering, the Federal University of Technology, Akure, Nigeria
-
I. A. Arighaye
Ondo State Ministry of Works, Department of Planning, Design, Research and Statistics, Akure, Nigeria
-
J. O. Afolayan
Department of Civil Engineering, the Federal University of Technology, Akure, Nigeria
-
- Keywords:
- Progressive failure, demand-capacity ratio, differential settlement, multiÂ-storey building, alternative load path method
- Abstract
-
Multi-Storey buildings are buildings with many floors above the ground floor, which serve as shelters for man, his properties and activities. Most building/ails because they were only designed for normal loads whereas abnormal loads were not considered. Therefore, this paper investigates the potential for progressive failure of multi-storey reiriforced concrete (RC) buildings under chosen varying degrees of settlement ranging between 2 5 mm and 15 0 mm. The computer-based modelling procedure following Alternative Load Path Method is adopted for progressive failure analysis. A 5-typical frame models based on the beams' cross-sectional dimensions were analyzed. Each of the frames is analyzed under the normal loads, combining with the assumed differential settlement. From the results obtained, it is discovered that the potential for progressive failure of a multi-storey RC building increases with the increase in the degree of differential settlement. At 25 mm to 75 mm settlement, vulnerability to progressive failure is very low as the Demand-Capacity-Ratio (DCR) values of the component members are very small, but from I 00 mm settlement and above the structure exhibits high potential for progressive failure. It is also noted that the potential for progressive failure of the structure decreases upwards the building storeys. The potential for progressive failure is higher in the lower floors than in the upper floors. Also, the rigidity of the structure helps in combating progressive failure under differential settlement.
- References
- Downloads
- Published
- 2020-04-09
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- Robert Oluwayimika Abolade, Oluwaseun Olayinka Tooki, David Oluwagbemiga Aborisade, REVIEW ARTICLE ON THE MITIGATION OF FOUR WAVE MIXING IN OPTICAL COMMUNICATION SYSTEM , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 1 (2021): FUTA Journal of Engineering and Engineering Technology
- J. A. Afelumo, O. A. Ademeso, Investigation of the Integrity of Subsoil as Foundation Support for a new Hostel Building, FUT, Akure, Southwestern Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 2 (2019): FUTA Journal of Engineering and Engineering Technology
- B. Adebayo, Evaluation of the Performance of Atlas Copco SDR4 Rotary Drill In Sagamu Limestone Formation, Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 1 (2019): FUTA Journal of Engineering and Engineering Technology
- A. O. Owolabi, P. A. Adesida, COST EVALUATION FOR ASPHALT PRODUCTION IN SELECTED QUARRIES , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 1 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- B. V. Omidiji, H. A. Owolabi, T. A. Morakinyo, A. Olukoga, Effects of Machining Parameters on the Surface Roughness of Al-Si alloy , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 9 No. 2 (2015): FUTA Journal of Engineering and Engineering Technology
- O. O. Olubanjo, Effects of Wastewaters From an Abattoir on Surface Water Quality in Akure, Ondo State, Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 1 (2017): FUTA Journal of Engineering and Engineering Technology
- J. M. Jabar, L. Lajide, A. O. Adetuyi, B. J. Owolabi, G. W. Ayoade, Chemical Modification of Coir, Empty Fruit Bunch and Palm Kernel Fibres for Polymer Reinforcement , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 1 (2017): FUTA Journal of Engineering and Engineering Technology
- Tasiu Ashiru Sulaiman, Ibrahim Aliyu, Yusuf Yau, Ibrahim Bello, ASSESSMENT OF GROUNDNUT SHELL ASH AND SAWDUST ASH AS PARTIAL REPLACEMENT OF CEMENT IN CONCRETE , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 2 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- A. O. Melodi, B. O. Akinloye, Transmission Capacity Enhancement for Nigerian Power Transmission Grid using TCSC and UPFC , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 8 No. 2 (2014): FUTA Journal of Engineering and Engineering Technology
- K. O. Oladosu, E. O. Olafimihan, K. A. Babatunde, B. Kareem, A. A. Mustapha, Investigation of Staged Air supply on Grate Combustion of Palm Kernel Shell Mixed with Selected additives (Al2O3 and CaO) , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 1 (2019): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.