PROGRESSIVE FAILURE ANALYSIS OF MULTI-STOREY REINFORCED CONCRETE BUILDINGS UNDER DIFFERENTIAL SETTLEMENT
- Authors
-
-
S. A. Alabi
Department of Civil Engineering, the Federal University of Technology, Akure, Nigeria
-
I. A. Arighaye
Ondo State Ministry of Works, Department of Planning, Design, Research and Statistics, Akure, Nigeria
-
J. O. Afolayan
Department of Civil Engineering, the Federal University of Technology, Akure, Nigeria
-
- Keywords:
- Progressive failure, demand-capacity ratio, differential settlement, multiÂ-storey building, alternative load path method
- Abstract
-
Multi-Storey buildings are buildings with many floors above the ground floor, which serve as shelters for man, his properties and activities. Most building/ails because they were only designed for normal loads whereas abnormal loads were not considered. Therefore, this paper investigates the potential for progressive failure of multi-storey reiriforced concrete (RC) buildings under chosen varying degrees of settlement ranging between 2 5 mm and 15 0 mm. The computer-based modelling procedure following Alternative Load Path Method is adopted for progressive failure analysis. A 5-typical frame models based on the beams' cross-sectional dimensions were analyzed. Each of the frames is analyzed under the normal loads, combining with the assumed differential settlement. From the results obtained, it is discovered that the potential for progressive failure of a multi-storey RC building increases with the increase in the degree of differential settlement. At 25 mm to 75 mm settlement, vulnerability to progressive failure is very low as the Demand-Capacity-Ratio (DCR) values of the component members are very small, but from I 00 mm settlement and above the structure exhibits high potential for progressive failure. It is also noted that the potential for progressive failure of the structure decreases upwards the building storeys. The potential for progressive failure is higher in the lower floors than in the upper floors. Also, the rigidity of the structure helps in combating progressive failure under differential settlement.
- References
- Downloads
- Published
- 2020-04-09
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- Oluseyi Orisadare, Ayodeji S. Olawore, Michael O. Ibiwoye, Eyitayo A. Ponle, Omolola T. Odeyemi, Opeyemi S. Kegbeyale, MECHANICAL AND MICROSTRUCTURAL PROPERTIES OF BRASS REINFORCED WITH COCONUT SHELL ASH POWDER , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 2 (2021): FUTA Journal of Engineering and Engineering Technology
- Charity Segun Odeyemi, Ayodeji Oladiran Awodugba, IMPROVING THE EFFICIENCY OF TITANIUM DIOXIDE BASED DYE SENSITIZED SOLAR CELL (DSSC) USING SILVER SURFACE COUNTER ELECTRODE , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 1 (2018): FUTA Journal of Engineering and Engineering Technology
- O. O. Awopetu, P. K. Farayibi, K. A. Ismail, Optimization of Major Process Parameters for Surface Roughness of ASTM 25 Grey Cast Iron using Taguchi method , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 2 (2017): FUTA Journal of Engineering and Engineering Technology
- Abayomi Olayiwola Eruola, Akeem Makinde, Gbenga Adegboyega Eruola, Kolawole Ayoola, Lugard Nwamini, EFFECT OF FLOAT-WEIGHTS ON DISCHARGE MEASUREMENT , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 1 (2021): FUTA Journal of Engineering and Engineering Technology
- O O. Daramola, MECHANICAL PROPERTIES AND WEAR BEHAVIOUR OF KAOLINITE CLAY PARTICLES REINFORCED EPOXY MATRIX COMPOSITES , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 2 (2021): FUTA Journal of Engineering and Engineering Technology
- S. S. Yaru, I. K. Adegun, M. A. Akintunde, Comparative Study on Ignition Time of Biogas from Cattle Dung and Mixtures of Cattle Dung with Cassava Peels , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 9 No. 1 (2015): FUTA Journal of Engineering and Engineering Technology
- Samuel L Akingbonmire, L Samuel, O Oluwafemi Omotayo, J O Afolayan, A Banjo Olorunshola, THE PHYSICO-CHEMICAL PROPERTIES OF SOME FINE AGGREGATES IN LOKOJA, NIGERIA , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 2 (2018): FUTA Journal of Engineering and Engineering Technology
- A. D. Akinwekomi, I. O. Oladele, A. Oyetunji, Microwave Sintering and Characterisation of Magnesium Alloy AZ61/Carbon Nanotube Composites , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 1 (2019): FUTA Journal of Engineering and Engineering Technology
- O.A. ADEMESO, B.I. ADEYEMO, Physical and Mechanical Characteristics of the Conglomeratic Layer in Akure, Southwestern Nigeria. , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 2 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- O OLANIRAN, J O BORODE, A E AFOLABI, P A OLUBAMBI, B A OLANIRAN, D O FOLORUNSO, CORROSION ASSESSMENT OF SINTER DUPLEX STAINLESS STEEL COMPOSITES IN PINEAPPLE JUICE EXTRACT , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 1 (2018): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.