PHYSICO-RHEOLOGICAL CHARACTERIZATION OF POLYMER MODIFIED BITUMEN
- Authors
-
-
E.O. OLUKANNI
Federal University of Technology, Akure, Nigeria
-
O.J. OYEDEPO
Federal University of Technology, Akure, Nigeria
-
- Keywords:
- Temperature Susceptibility, Complex Modulus, Bitumen, Polymer, Rheology
- Abstract
-
The demand for better performing roads has encouraged the development of alternative materials to modify asphalt binders. This research carried out a physico-rheological characterization of polymer-modified bitumen. Styrene-butadiene-styrene (SBS), Polyethylene Terephthalate (PET) and Ethylene-vinyl Acetate (EVA) were used to partially replace bitumen in proportion of 10%, 20%, 30%, 40%, and 50%. The physical characterization was done by determining the Penetration Index (PI) of bitumen and polymer modified bitumen (PMB) according to Van Der Poel nomograph. Rheological properties of bitumen and PMB were investigated by performing a dynamic mechanical analysis (DMA) in accordance with ASTM D 7175-15. The PI result indicated that the PI of PET modified bitumen ranged between 0.07 and 2.38, SBS modified bitumen has PI values that ranged between 0.61 to 3.08 and EVA modified bitumen is characterized with PI values that ranged between 0.78 and 3.11. The DMA of bitumen and PMB showed that PMB has a very high complex modulus especially PET modified bitumen with the highest complex modulus of 5310 kPa at 30% partial replacement; this is an indication of high resistance to thermal and plastic deformation which is as a result of the formation of a tough, rigid, three-dimensional network. It can thus be concluded that PET, SBS and EVA are good modifiers of bitumen as they are capable of increasing specific properties of bitumen.
- References
- Downloads
- Published
- 2020-11-21
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- I. A. Daniyan, E. I. Bello, T. I. Ogedengbe, L. Lajide, P. B. Mogaji, Development of a Model For Predicting the Yield of Biodiesel During Biodiesel Production , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 10 No. 1 (2016): FUTA Journal of Engineering and Engineering Technology
- O O. Daramola, MECHANICAL PROPERTIES AND WEAR BEHAVIOUR OF KAOLINITE CLAY PARTICLES REINFORCED EPOXY MATRIX COMPOSITES , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 2 (2021): FUTA Journal of Engineering and Engineering Technology
- A. O. Melodi, B. O. Akinloye, Transmission Capacity Enhancement for Nigerian Power Transmission Grid using TCSC and UPFC , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 8 No. 2 (2014): FUTA Journal of Engineering and Engineering Technology
- A. P. Olalusi, Comparison of Selected Engineering Properties of Two Species of Cocoyam Essential for Handling of the Tubers , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 8 No. 2 (2014): FUTA Journal of Engineering and Engineering Technology
- A Amoko, S JUSTINAH, A Fehintola, O Ezekiel, I Oke, A Isaiah, EVALUATION OF EFFECTS OF SELECTED FACTORS ON ADSORPTION KINETICS OF LEAD ION REMOVAL FROM AQUEOUS SOLUTIONS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 2 (2018): FUTA Journal of Engineering and Engineering Technology
- T O Awodola, FLEXURAL MOTION UNDER MOVING MASSES OF PRESTRESSED SIMPLY SUPPORTED PLATE RESTING ON BI-PARAMETRIC FOUNDATION , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 1 (2018): FUTA Journal of Engineering and Engineering Technology
- A. Fadeyibi, Z. D. Osunde, M. G. Visa, A. A. Okunola, Investigation into properties of starch-based nanocomposite materials for fruits and vegetables packaging - A review , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 1 (2017): FUTA Journal of Engineering and Engineering Technology
- O. O. Olubanjo, Assessment of Groundwater Quality For Human Consumption And Agricultural Use In Ilara-Mokin, Ondo State, Nigeria. , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 10 No. 2 (2016): FUTA Journal of Engineering and Engineering Technology
- O OLANIRAN, J O BORODE, A E AFOLABI, P A OLUBAMBI, B A OLANIRAN, D O FOLORUNSO, CORROSION ASSESSMENT OF SINTER DUPLEX STAINLESS STEEL COMPOSITES IN PINEAPPLE JUICE EXTRACT , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 1 (2018): FUTA Journal of Engineering and Engineering Technology
- I O OLADELE, O O DARAMOLA, A M OKORO, J A OMOTOYINBO, EVALUATION OF THE EFFECT OF MERCERIZED WHITE CHICKEN FEATHER FIBRES ON THE MECHANICAL , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 1 (2018): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.