FLEXURAL MOTION UNDER MOVING MASSES OF PRESTRESSED SIMPLY SUPPORTED PLATE RESTING ON BI-PARAMETRIC FOUNDATION
- Authors
-
-
T O Awodola
Department of Mathematics, Federal University of Technology, Akure, Nigeria
-
- Keywords:
- Prestress, Rotatory Inertia, Bi-parametric Foundation, Resonance, Critical speed, Mass Ratio.
- Abstract
-
In this investigation, the flexural vibration of a prestressed and simply supported rectangular plate carrying moving concentrated masses and resting on bi-parametric (Pasternak) elastic foundation is considered. In order to solve the governing fourth order partial differential equation, a technique based on separation of variables is used to reduce the equation with variable and singular coefficients to a sequence of coupled second order ordinary differential equations. The modified method of Struble and the integral transformations are then employed for the solutions of the reduced equations. The numerical results in plotted curves show that as the value of the axial force in x-direction (Nx) increases, the response amplitudes of the plates decrease, the same effect is produced as the axial force in y-direction (Ny) increases for both cases of moving force and moving mass problems of the prestressed and simply supported rectangular plate resting on Pasternak elastic foundation. The deflection of the plate also decreases in each case as the values of the Shear modulus Go and the rotatory inertia correction factor Ro increase. Also, the transverse deflections of the prestressed rectangular plates under the actions of moving masses are higher than those obtained when only the force effects of the moving loads are considered. Further analysis shows that resonance is attained earlier in moving mass problem than in moving force problem and that the critical speed for the moving mass problem is reached prior to that of the moving force problem, implying that it is risky to rely on a design based on the moving force solution. Furthermore, the response amplitudes of the moving mass problem increase with increasing mass ratio and approach those of the moving force as the mass ratio approaches zero for the prestressed and simply supported rectangular plates resting on uniform Pasternak elastic foundation
- References
- Downloads
- Published
- 2019-04-29
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- T. O. Awodola, Dynamic Behaviour Under Moving Masses of Prestressed and Elastically Supported Plates Resting on Winkler Foundation , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 9 No. 1 (2015): FUTA Journal of Engineering and Engineering Technology
- O. A. Adetola, O. J. Olukunle, T. L. Aremu, Investigation of The Effects of Yield On Selected Physical Properties of Cassava Tubers , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 10 No. 2 (2016): FUTA Journal of Engineering and Engineering Technology
- A. M. Akintade, O. J. Olukunle, J. Isa, Performance Evaluation of an Electromechanical Groundnut Roasting Machine Akintade A.M, Olukunle O. J. and Isa J. , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 8 No. 2 (2014): FUTA Journal of Engineering and Engineering Technology
- I. A. Daniyan, E. I. Bello, T. I. Ogedengbe, L. Lajide, P. B. Mogaji, Development of a Model For Predicting the Yield of Biodiesel During Biodiesel Production , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 10 No. 1 (2016): FUTA Journal of Engineering and Engineering Technology
- E. I. Bello, I. A. Daniyan, T. I Ogedengbe, L. Lajide, P. B. Mogaji, Development of a Model for Predicting the Yield of Biodiesel During Biodiesel Production , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 11 No. 1 (2017): FUTA Journal of Engineering and Engineering Technology
- S. S. Yaru, POLLUTION OF VEHICULAR EMISSION ANALYSIS AT FEDERAL UNIVERSITY OF TECHNOLOGY AKURE NORTH GATE , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 1 (2021): FUTA Journal of Engineering and Engineering Technology
- B. V. Omidiji, H. A. Owolabi, T. A. Morakinyo, A. Olukoga, Effects of Machining Parameters on the Surface Roughness of Al-Si alloy , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 9 No. 2 (2015): FUTA Journal of Engineering and Engineering Technology
- Anthony T. Bolarinwa, Gideon C. Nwafor, OPEN PIT OPTIMIZATION AND PRODUCTION SCHEDULING OF OKOBO COAL MINE, CENTRAL NIGERIA , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 1 (2018): FUTA Journal of Engineering and Engineering Technology
- Olanrewaju Oluwafemi Akinfala, Emmanuel Enyeribe Ege, Ladi Folorunso Ogunwolu, ARRIVAL PATTERNS AND TRAFFIC FLOW CHARACTERISTICS AT SIGNALIZED INTERSECTIONS: CONSIDERING UPSTREAM SIGNAL INFLUENCE AND TIME RESOLUTIONS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 1 (2021): FUTA Journal of Engineering and Engineering Technology
- B. O. Akinnuli, S. P Ayodeji, S. O. Abadariki, J. O. Fasan, Design, Fabrication and Performance Evaluation of a Reciprocating Cocoa Pod Breaking Machine , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 8 No. 1 (2014): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.