IMPACT HAMMER TEST FOR BAYESIAN PARAMETER IDENTIFICATION OF RAILWAY TRACK SYSTEM
- Authors
-
-
S.A. ALABI
Federal University of Technology, Akure, Nigeria
-
- Keywords:
- ballasted track, field test, Bayesian model updating, MCMC, low-amplitude vibration
- Abstract
-
The current design approach of railway sleeper is majorly based on some simplifications considered in the European guidelines. One example of these simplifications is how the distribution of the ballast under the sleeper is accounted for. When ballast is damaged, the stiffness it provided to support the sleeper is reduced and the dynamic behavior of the sleeper changes. However, these guidelines consider a uniform distribution of ballast stiffness, either along the complete length of the sleeper or limited to the rail seat. The embedding ballast conditions of railway tracks seemingly vary randomly from site to site and the ballast-sleeper interaction is neither uniformly distributed nor fixed. Therefore, there is need to evaluate the health status of the ballast under the existing railway track. A field test was carried out on an existing ballasted track, to obtain the time domain responses under impact excitation. The measured vertical vibrations at different locations on the in-situ sleeper were employed in time-domain Markov chain Monte Carlo (MCMC)-based Bayesian model updating for identification of the railway track system. MCMC was used to ensure that proposed method can be applied even when the problem is unidentifiable. The proposed method identified the distribution of railway ballast stiffness under low-amplitude vibration and the “equivalent†rail stiffness and mass. The model updating results confirmed that the ballast stiffness under the existing sleeper was uniform, which implies that there was no ballast damage under the tested sleeper.
- References
- Downloads
- Published
- 2020-11-24
- Section
- Articles
- License
-
Copyright
With the submission of a manuscript, the corresponding author confirms that the manuscript is not under consideration by another journal. With the acceptance of a manuscript, the Journal reserves the exclusive right of publication and dissemination of the information contained in the article. The veracity of the paper and all the claims therein is solely the opinion of the authors not the journal.
How to Cite
Similar Articles
- A. A. Ponnle, S. K. Ani, Assessment of Exposure to Indoor Power Frequency Magnetic Fields: SEET Building and Engineering Laboratories, FUTA , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 1 (2019): FUTA Journal of Engineering and Engineering Technology
- C. O. Ijagbemi, D. T. Oloruntoba, A. O. Adeoye, Development of a Bioplastic Film for Food Packaging , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 8 No. 1 (2014): FUTA Journal of Engineering and Engineering Technology
- Taiwo Olabanji, EVALUATION OF DELONIX REGIA SEEDS AS A NATURAL COAGULANT IN THE TREATMENT OF LOW TURBID WATER , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 2 (2021): FUTA Journal of Engineering and Engineering Technology
- B. O. Akinnuli, S. P Ayodeji, S. O. Abadariki, J. O. Fasan, Design, Fabrication and Performance Evaluation of a Reciprocating Cocoa Pod Breaking Machine , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 8 No. 1 (2014): FUTA Journal of Engineering and Engineering Technology
- Kayode Francis Akingbade, DEVELOPMENT OF CHEMICAL PROPORTION FORMULATION MODEL FOR QUALITY CONTROL IN FLEXIBLE POLYURETHANE FOAM PRODUCTION , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 2 (2018): FUTA Journal of Engineering and Engineering Technology
- Y. O. Olasoji, S. A. Oyetunji, Propagation Path Loss Model for FM Radio Stations In South West, Nigeria , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 14 No. 1 (2020): FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY
- Catherine Mayowa Ikumapayi, Samuel Lambe Akingbonmire, EFFECTS OF BAMBOO LEAF AND LOCUST BEANS POD ASHES ON AUTOGENOUS SHRINKAGE STRAIN AND COMPRESSIVE STRENGTH OF MORTAR , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 12 No. 1 (2018): FUTA Journal of Engineering and Engineering Technology
- O O. Daramola, MECHANICAL PROPERTIES AND WEAR BEHAVIOUR OF KAOLINITE CLAY PARTICLES REINFORCED EPOXY MATRIX COMPOSITES , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 2 (2021): FUTA Journal of Engineering and Engineering Technology
- I. A. Oke, A. O. Obijole, E. A. Adekunbi, J. O. Babajide, M. D. Idi, T. A. Aladesanmi, THERMAL PROPERTY OF CARBON RESIN ELECTRODES DEVELOPED FOR ELECTROCHEMICAL TREATMENT OF WATER AND WASTEWATERS , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 15 No. 1 (2021): FUTA Journal of Engineering and Engineering Technology
- O. A. Dahunsi, M. O. Adeoti, O. O. Awopetu, F. O. Aramide, O. O. Alabi, A. S. Abdulkareem, Characterization of Saman-Burkono (Nigeria) Graphite for Crucible Production , FUTA JOURNAL OF ENGINEERING AND ENGINEERING TECHNOLOGY: Vol. 13 No. 1 (2019): FUTA Journal of Engineering and Engineering Technology
You may also start an advanced similarity search for this article.